Results 21 to 30 of about 224,369 (149)
Advanced Engineering Materials, EarlyView.The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study presents a reversible temperature sensor with high switching ratio, ∼103. The device is fabricated using PET‐ITO and carbon nanotube dispersions in alkane. Considering its application in cold chain logistics, a proof‐of‐concept with LED is showcased. Thus, a temperature drop below the threshold temperature (crystallization temperature of the
Sunil Kumar Behera +8 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley +1 more source
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study explored how effective nickel aluminide coatings are obtained in providing oxidation resistance applied to the Inconel 738 alloy, modeling with diffusion models. In the present study, kinetics and thermal behavior of the Inconel 738 alloy were studied by the low‐temperature thermoreactive aluminizing process, which was carried out at 625°C ...
Gozde Celebi Efe +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
A Compact Spin‐Coated Graphene UWB Antenna for Breast Tumor Detection
Advanced Engineering Materials, EarlyView.A compact, spin‐coated graphene ultra‐wideband patch antenna designed for breast tumor detection, capable of distinguishing between malignant and benign tumors. This innovative antenna can serve as an effective initial screening tool, particularly in resource‐limited settings such as rural areas, where access to advanced medical equipment like MRI and ...
Raja Rashidul Hasan +9 more
wiley +1 more source
Zein‐Based Adhesives: Sustainable Extraction and Application in Bioadhesive Technologies
Advanced Engineering Materials, EarlyView.Zein is extracted from corn gluten meal using a simple and scalable process with high yield (~90%). The resulting protein is applied in bioadhesives modified with Ca2+ and Fe3+ ions, exhibiting substrate‐dependent adhesion. The findings demonstrate competitive bonding performance and highlight the role of ionic interactions in tuning adhesion ...
Paula Bertolino Sanvezzo +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Trace additions of Sn and Sr combined with a two‐step aging treatment are shown to enhance the microstructure and performance of Al–Zr–Sc conductor alloys. Strength and electrical conductivity increase concurrently through accelerated precipitation of fine Al3(Sc, Zr) precipitates and improved dislocation resistance, offering a cost‐effective pathway ...
Quan Shao +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.A hierarchical porous copper current collector is fabricated via three‐dimensional printing combined with pressureless sintering to stabilize lithium metal anodes. The interconnected architecture lowers local current density, guides uniform Li deposition within pores, and suppresses dendrite growth.
Alok Kumar Mishra, Mukul Shukla
wiley +1 more source