Results 191 to 200 of about 9,707 (256)

Effects of Causal Beliefs About Gout on Public Views About Gout Management: A Randomized Experimental Study

Arthritis Care &Research, EarlyView.
Objective Despite well‐described biologic causes, the public views unhealthy lifestyle choices as the primary cause of gout. This study investigated how causal beliefs about gout influence the public's views about its management. Methods In a randomized study, 201 members of the public viewed one of two 2‐minute videos about gout.
Rachel Murdoch, Borislav Mihov, Anne Horne, Keith J. Petrie, Gregory D. Gamble, Lachlan Fleck, Nicola Dalbeth   +6 more
wiley   +1 more source

Biopsychosocial Determinants of Hand Function and Its Trajectories Over Five Years in Patients With Hand Osteoarthritis

Arthritis Care &Research, EarlyView.
Objective This study aimed to investigate hand function trajectories over five years in primary hand osteoarthritis (OA). Additionally, determinants of baseline and longitudinal hand function were assessed. Methods A total of 538 patients with both baseline and five‐year study visits were analyzed.
Annemiek V. E. M. Olde Meule, Coen van der Meulen, Jos Runhaar, Frits R. Rosendaal, Margreet Kloppenburg   +4 more
wiley   +1 more source

Perceived Impacts and Predictors of Cannabis Products Used by Patients with Rheumatologic Conditions in Alberta, Canada: A Multivariable Analysis of Cross‐Sectional Survey Data

Arthritis Care &Research, EarlyView.
Objective This study aimed to characterize cannabis product choices (cannabinoid content and formulation) among patients with rheumatologic conditions and their associations with patient factors, patient‐reported perceived side effects, and positive impacts.
Susan Zhang, Samuel A.J. Lowe, Frank Sun, Allyson Jones, Tarek Turk, Joanne Olson, Pauline Paul, Shelby Yamamoto, Linda Kolewaski, Elaine Yacyshyn, Cheryl A. Sadowski   +10 more
wiley   +1 more source

Mechanochemical Synthesis and Characterization of Nanostructured ErB4 and NdB4 Rare‐Earth Tetraborides

Advanced Engineering Materials, Volume 27, Issue 6, March 2025.
ErB4 and NdB4 nanostructured powders are produced by mechanochemical synthesis. 5 h mechanical alloying and 4 M HCl acid leaching are used in the production. ErB4 and NdB4 powders exhibit maximum magnetization of 0.4726 emu g−1 accompanied with an antiferromagnetic‐to‐paramagnetic phase transition at about TN = 18 K and 0.132 emu g−1 with a maximum at ...
Burçak Boztemur, Faruk Kaya, Bora Derin, Mustafa Lütfi Öveçoğlu, Ju Li, Duygu Ağaoğulları   +5 more
wiley   +1 more source

Revisiting Stability Criteria in Ball‐Milled High‐Entropy Alloys: Do Hume–Rothery and Thermodynamic Rules Equally Apply?

Advanced Engineering Materials, Volume 27, Issue 6, March 2025.
The stability criteria affecting the formation of high‐entropy alloys, particularly focusing in supersaturated solid solutions produced by mechanical alloying, are analyzed. Criteria based on Hume–Rothery rules are distinguished from those derived from thermodynamic relations. The formers are generally applicable to mechanically alloyed samples.
Javier S. Blázquez, Alejandro F. Manchón‐Gordón, Antonio Vidal‐Crespo, Rafael Caballero‐Flores, Jhon J. Ipus, Clara F. Conde   +5 more
wiley   +1 more source

Characterization of Defect Distribution in an Additively Manufactured AlSi10Mg as a Function of Processing Parameters and Correlations with Extreme Value Statistics

Advanced Engineering Materials, EarlyView.
Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt, Varma Kvvssn, Hossein Laieghi, Zia Uddin, Peyman Ansari, E. Kıvanç Sadak, Can Barış Toprak, Hüseyin Kızıl, Enrico Salvati   +8 more
wiley   +1 more source

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

Laser Powder Bed Fusion of Alumina: Effects of Scanning Strategies on External and Internal Defects

Advanced Engineering Materials, EarlyView.
This study investigates how scanning strategies affect pure alumina in laser powder bed fusion. Linear 45° scanning yields uniform surfaces but high porosity, while the island‐concentric strategy provides higher density with through‐holes favorable for infiltration. Findings highlight pathways toward optimizing defect‐free alumina parts.
Mohamed Abdelmoula, Gökhan Küçüktürk, Duran Kaya, David Grossin, Christophe Tenailleau, Benjamin Duployer, Enrique Juste, Fabrice Petit   +7 more
wiley   +1 more source

Carboxylic‐Acid Functionalized Multiwalled Carbon Nanotube‐Alkane‐Based Resistive Temperature Sensor for Cold Chain Applications

Advanced Engineering Materials, EarlyView.
This study presents a reversible temperature sensor with high switching ratio, ∼103. The device is fabricated using PET‐ITO and carbon nanotube dispersions in alkane. Considering its application in cold chain logistics, a proof‐of‐concept with LED is showcased. Thus, a temperature drop below the threshold temperature (crystallization temperature of the
Sunil Kumar Behera, Philippe Marrec, A. Jorge Parola, Madalena Dionísio, Hugo Águas, Andreia F. M. Santos, Hamed Pourkheirollah, Donald Lupo, César A. T. Laia   +8 more
wiley   +1 more source

Low‐Cost, Large‐Scale Nanoporous Metals by Mechanical Alloying, Oxide Reduction, and Dealloying of Powders

Advanced Engineering Materials, EarlyView.
Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley   +1 more source