Distinct Roles for Bacterial and Fungal Communities During the Curing of Vanilla
Frontiers in Microbiology, 2020 Vanilla produces aroma after curing. There were a few reports about the possible involvement of microorganisms during the curing process. Bacterial and fungal community was analyzed to explore the distinct roles.
Fei Xu +8 more
doaj +1 more source
Applied Sciences, 2020 This work presents a new method to determine the evolution of the dynamic Young’s modulus (MOE) from small mechanical disturbances caused by cement mortar samples and whose value is collected using a low-cost Arduino accelerometer.
Engerst Yedra +3 more
doaj +1 more source
Sequential curing of thiol-acetoacetate-acrylate thermosets by latent Michael addition reactions [PDF]
, 2017 Thiol-acetoacetate-acrylate ternary dual-curing thermosets were prepared by a sequential process consisting of thiol-Michael addition to acrylates at room temperature followed by Michael addition of acetoacetates to acrylates at moderately elevated ...
Fernández Francos, Xavier +5 more
core +2 more sources
Non-destructive evaluation of an infusion process using capacitive sensing technique [PDF]
, 2016 In this study, a capacitive sensing based non-destructive evaluation technique is applied to a vacuum assisted resin infusion process for the fabrication of glass fibre reinforced composites, as such different steps of the fabrication process (the ...
Bossuyt, Frederick +7 more
core +1 more source
Degree of cure‐dependent modelling for polymer curing processes at small strains [PDF]
PAMM, 2013 AbstractIn this paper, a thermodynamically consistent small strain constitutive model is formulated that is directly based on the degree of cure, a key parameter in the curing (reaction) kinetics. The new formulation is also in line with the earlier proposed hypoelastic approach, cf. Hossain et al., 2010.
Hossain, Mokarram +2 more
openaire +1 more source
Use of Parameter Estimation for Stereolithography Surface Finish Improvement [PDF]
, 2005 In order to improve Stereolithography (SLA) surface finish, a systematic approach based on estimation of process parameters is needed. In this paper, the exposure on a desired SLA build surface is formulated as a function of process parameters.
Rosen, David W., Sager, Benay
core +1 more source
Evaluation of in-situ shrinkage and expansion properties of polymer composite materials for adhesive anchor systems by a novel approach based on digital image correlation [PDF]
, 2019 The curing reaction of thermosetting resins is associated with chemical shrinkage which is overlapped with thermal expansion as a result of the exothermal enthalpy. Final material properties of the polymer are determined by this critical process.
Lichtenegger, Helga C. +5 more
core +1 more source
Investigating the impact of curing system on structure-property relationship of natural rubber modified with brewery by-product and ground tire rubber [PDF]
, 2020 The application of wastes as a filler/reinforcement phase in polymers is a new strategy to modify the performance properties and reduce the price of biocomposites.
Cañavate Ávila, Francisco Javier +5 more
core +3 more sources
In situ monitoring of epoxy resin curing process: Using glass transition as a bridge
Polymer Testing, 2023 Dielectric analysis (DEA) is an effective method for monitoring the curing process of epoxy resin (EP) in situ, but the influence of curing temperature on the measurement results limits the application of DEA in curing process monitoring with variable ...
Zhicheng Wu +5 more
doaj +1 more source
Phenomenological characterization of sequential dual-curing of off-stoichiometric "thiol-epoxy" systems: Towards applicability [PDF]
, 2017 An extensive characterization of a sequential dual-curing system based on off-stoichiometric “thiol-epoxy” mixtures was carried out using thiol compounds of different functionality.
Belmonte, Alberto +3 more
core +1 more source