Results 41 to 50 of about 7,207,987 (296)

General Analytical Model of Magnet Average Eddy-Current Volume Losses for Comparison of Multi-phase PM Machines with Concentrated Winding [PDF]

open access: yes, 2014
this paper studies magnet eddy-current losses in permanent magnet (PM) machines with concentrated winding. First of all, space harmonics of magnetomotive force (MMF) and their influence on magnet losses in electrical machines are investigated.
LEGRANGER, Jerome   +2 more
core   +1 more source

Uniform Amorphization of Crystalline Silicon Surfaces Enabled by Deep Ultraviolet Femtosecond Laser Pulses

open access: yesAdvanced Engineering Materials, EarlyView.
Deep‐UV (258 nm) femtosecond pulses enable uniform amorphous silicon writing on Si(100)/(111) with a six‐fold larger fluence amorphization window than NIR methods. Optimized fluence and overlap yield 20–45 nm uniform and continuous amorphous layers. Microscopy shows sharp interfaces, and real‐time reflectivity reveals nanosecond melt–resolidification ...
Wissal Benali   +5 more
wiley   +1 more source

Analytical Investigation of Primary Waveform Distortion Effect on Magnetic Flux Density in the Magnetic Core of Inductive Current Transformer and Its Transformation Accuracy

open access: yesSensors
This paper analyzes how distortion in the primary current waveform affects the magnetic flux density in the magnetic core of an inductive current transformer and its transformation accuracy.
Michal Kaczmarek, Kacper Blus
doaj   +1 more source

Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning

open access: yesAdvanced Engineering Materials, EarlyView.
The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley   +1 more source

Materials‐Driven Additive Manufacturing for Electrical Machines: Qualification‐Oriented Design Beyond Geometric Freedom

open access: yesAdvanced Engineering Materials, EarlyView.
This perspective reframes additive manufacturing for electrical machines as a qualification‐limited materials and architecture design problem. It links process–structure–property–performance relationships to magnetic, conducting, dielectric, and thermal property windows, highlighting where AM can enable segmented magnetic circuits, permanent magnet ...
Dénes Fodor, Loránd Szabó
wiley   +1 more source

A Selective Harmonic Current Detection Algorithm Based on Quadrature Theory

open access: yesKongzhi Yu Xinxi Jishu, 2015
Aiming at the harmonics current detection methods of power grid, a simple effective harmonics current detection algorithm was introduced based on quadrature theory,and its realization and optimization methods were given.
LI Yu, LANG Fengjie, MA Zhe, WANG Xutao
doaj  

A Methodology for High-Power Drives Emulation Using a Back-to-Back Configuration

open access: yesIEEE Access, 2022
Validation of high-power converters at the development stage often cannot be performed using the real load. A testbench consisting of the Equipment Under Test (i.e., tested power converter) and an auxiliary power converter, preferably using power ...
Fernando Briz   +6 more
doaj   +1 more source

Chemical State Detection and Charge Transfer in Complex Oxide Heterostructures via In Situ Auger Electron Spectroscopy

open access: yesAdvanced Functional Materials, EarlyView.
In situ Auger Electron Spectroscopy resolves oxidation states with high fidelity during the pulsed laser deposition of multivalent perovskite manganate and vanadate heterostructures. The chemical‐state signature is carried by the valence‐electron population of the transition‐metal cation, read out through the relative intensities of Auger fine ...
Harish Kumarasubramanian   +1 more
wiley   +1 more source

Two‐Photon Grayscale Lithography (2GL) of High Mechanical and Optical Quality 3D Silica Glass Microstructures

open access: yesAdvanced Functional Materials, EarlyView.
Two‐photon grayscale lithography (2GL) enables high‐speed and precise 3D printing of thermolyzed silica glass microstructures with optical‐grade surface quality, high quality factors, and mechanical strength utilizing a custom‐made pre‐glass resist based on polyhedral oligomeric silsesquioxane (POSS) modified with a high‐sensitivity Norrish type II ...
Jonathan L. G. Schneider   +4 more
wiley   +1 more source

Vascular dementia: current concepts and nomenclature harmonization [PDF]

open access: yesDementia & Neuropsychologia, 2012
ABSTRACT Several types of cerebrovascular lesions are associated with cognitive decline, but the role of each type in dementia manifestation has yet to be determined. One of the greatest barriers of conducting clinicopathological studies in vascular dementia concerns the overlapping of nomenclature for these lesions.
openaire   +7 more sources

Home - About - Disclaimer - Privacy