Results 131 to 140 of about 20,473 (218)

Applying transformer-based deep learning models in image-driven cancer diagnosis: a comprehensive bibliometric analysis of global research trends. [PDF]

Front Oncol
Gong L, Wen T, Zeng X, Liu X, Li M, Sun J, Zheng J.   +6 more
europepmc   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Dynamic adjustment algorithm of equipment maintenance cycle based on substation state operation and maintenance. [PDF]

PLoS One
Yan Y, Zhou F, Cai Z, Lu H.
europepmc   +1 more source

Over Current Characteristrcs of Current Transformers

The Journal of the Institute of Electrical Engineers of Japan, 1948
Nishino, Osamu, Ikeda, Mioji
openaire   +1 more source

Additive Gaussian Process Regression for Predictive Design of High‐Performance, Printable Silicones

Advanced Engineering Materials, EarlyView.
A chemistry‐aware design framework for tuning printable polydimethylsiloxane (PDMS) for vat photopolymerization (VPP) is developed using additive Gaussian process (GP) modeling. Polymer network mechanics informs variable groupings, feasible formulation constraints, and interaction variables.
Roxana Carbonell, Martha Leach, Hongtao Song, Carolyn Seepersad   +3 more
wiley   +1 more source

Multi-modal fusion fault diagnosis for high-voltage transformers based on STFT-ResBIGRUNet. [PDF]

Sci Rep
Yuan J, Liu C, Zheng B, Pan M.
europepmc   +1 more source

Thermodynamic Pathways of Nonequilibrium Solidification in Wire‐Arc Additive Manufacturing Fe‐Based Multicomponent Alloy Structures

Advanced Engineering Materials, EarlyView.
Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios, Anthony Gonzalez, Aleksander Aleman, Tyler Dolmetsch, Tanaji Paul, Arvind Agarwal   +5 more
wiley   +1 more source

Tailored Hierarchical Porous Copper Architectures via Three Dimensional Printing and Pressure‐less Sintering for Next‐Generation Lithium‐Metal Batteries

Advanced Engineering Materials, EarlyView.
A hierarchical porous copper current collector is fabricated via three‐dimensional printing combined with pressureless sintering to stabilize lithium metal anodes. The interconnected architecture lowers local current density, guides uniform Li deposition within pores, and suppresses dendrite growth.
Alok Kumar Mishra, Mukul Shukla
wiley   +1 more source

Multi-source harmonic estimation method for distribution networks based on variational modal decomposition. [PDF]

PLoS One
Zuo H, Xu H, Wang Z, Yu Z, Wu Z.
europepmc   +1 more source

Composition‐Tuned Enhancement of the Anomalous Nernst Effect in FeCo–Pt Thin Films on Rigid and Flexible Substrates

Advanced Engineering Materials, EarlyView.
Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi, Hiroyuki Awano, Kenji Tanabe   +2 more
wiley   +1 more source