Results 131 to 140 of about 2,290,071 (246)

Enhancement of the Through‐Thickness Electrical Conductivity of Carbon‐Fiber‐Reinforced Plastics Using Large Graphite Particles

Advanced Engineering Materials, EarlyView.
To enhance through‐thickness conductivity without sacrificing impregnation, large spherical graphite particles are intentionally employed in a low‐viscosity resin. Unlike finer conductive fillers, these particles remain outside the fiber bundles and accumulate in resin‐rich interlaminar regions during molding.
Keito Hosoe, Yu Zhou, Shintaro Kamiyama, Takao Okada, Tomohiro Yokozeki, Ryoma Tokonami, Tatsuhiro Takahashi   +6 more
wiley   +1 more source

Dynamic Cutting Force Prediction Model and Experimental Investigation of Ultrasonic Vibration-Assisted Sawing. [PDF]

Micromachines (Basel)
Wang Y, Wang Y, Ni P, Qu S, Yuan Q, Wang H, Lei X, Wang J, Wang Y.   +8 more
europepmc   +1 more source

Modeling Evolution of Cutting Force in Ultrasonically Assisted Drilling of Carbon Fiber Reinforced Plastics. [PDF]

Materials (Basel), 2022
Huang CR, Liao BM, Kai CY, Su CM, Hung JP.   +4 more
europepmc   +1 more source

3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement

Advanced Engineering Materials, EarlyView.
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin, Gloria R. Young, Francesca Tallia, Reece N. Oosterbeek, Shaaz Ghouse, Edward Spiers, Nupur Kohli, Tom Briggs, Marc Masen, Siwei Li, Ren‐Jei Chung, Jonathan R. T. Jeffers, Julian R. Jones   +12 more
wiley   +1 more source

Three-Dimensional Cutting Force Model and Experimental Study of Diamond Bead Wire Saw Cutting of Loaded Coal. [PDF]

Materials (Basel)
Li S, Lv C, Qian Y, Yi M, Yang Y, Tang Z, Huang X, Zhao T.   +7 more
europepmc   +1 more source

A Novel Multivariate Cutting Force-Based Tool Wear Monitoring Method Using One-Dimensional Convolutional Neural Network. [PDF]

Sensors (Basel), 2022
Yang X, Yuan R, Lv Y, Li L, Song H.
europepmc   +1 more source

The Role of Ultra‐Thin Passive Films and Organic Adsorbates on Aluminum Chips for a Friction‐Induced Solid‐State Recycling Process

Advanced Engineering Materials, EarlyView.
Despite benefits to storage stability and handleability of aluminum scrap, octadecyl phosphonic acid (ODPA) SAMs reduce the tensile strength of wires produced using friction‐induced recycling. Etching and methyl diphosphonic acid (MDPA) coatings, however, have little effect.
Timothy D. Goller, Steffen Gabsa, Werner Homberg, Guido Grundmeier   +3 more
wiley   +1 more source

Experimental Investigation on Cutting Force and Hole Quality in Milling of Ti-6Al-4V. [PDF]

Micromachines (Basel)
Zhu L, Zhang K, Liu B, Jiang F, Wu X, Zhai L, Huang F, You W, Xu T, Zhang S, Guo R, Xue Y, Chen X.   +12 more
europepmc   +1 more source

Methodology for Evaluating the Cutting Force of Planar Technical Blades Used in Flatfish Processing. [PDF]

Micromachines (Basel), 2021
Zieliński B, Chaciński T, Pimenov DY, Nadolny K.   +3 more
europepmc   +1 more source

Elastic–Plastic Modeling and Experimental Characterization of Granular Jamming Actuators

Advanced Engineering Materials, EarlyView.
Granular jamming enables rapid switching between soft and rigid mechanical states. Here, a reduced‐order elastic‐perfectly‐plastic beam framework captures pressure‐dependent loading, unloading, residual deformation, and hysteresis in jammed beams, while matching three‐point bending experiments across materials and geometries. The framework links design
Saheli Patel, Prashant K. Purohit, Jordan R. Raney   +2 more
wiley   +1 more source