Results 211 to 220 of about 42,092 (305)

Signal and Contrast Optimization With Predicted Excitations (SCOPE) for Accelerating Large FOV Body Imaging at UHF. [PDF]

Magn Reson Med
Haluptzok TD, Schmidt S, Metzger GJ.
europepmc   +1 more source

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

Effects of cryogenic cooling on cutting temperature and surface roughness in turning of AA7075 aluminum alloy. [PDF]

Sci Rep
Ranjbar S, Foorginejad A, Emam SM, Ebadi M, Shiri K.   +4 more
europepmc   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

Impact of Downward Load and Rotational Kinematics on Root Canal Instrumentation with a Heat-Treated Nickel-Titanium Rotary Instrument. [PDF]

Materials (Basel)
Yamamoto R, Maki K, Kimura S, Omori S, Hirano K, Ebihara A, Yahata Y, Okiji T.   +7 more
europepmc   +1 more source

Ductile mode cutting of lithium niobate

Journal of the Japan Society for Abrasive Technology, 2012
SHIZUKA, Hiroo, OKUDA, Koichi, NUNOBIKI, Masayuki, LI, Wei, INAOKA, Takanobu, SAIKI, Tsunemasa, UTSUMI, Yuichi   +6 more
openaire   +1 more source

Zein‐Based Adhesives: Sustainable Extraction and Application in Bioadhesive Technologies

Advanced Engineering Materials, EarlyView.
Zein is extracted from corn gluten meal using a simple and scalable process with high yield (~90%). The resulting protein is applied in bioadhesives modified with Ca2+ and Fe3+ ions, exhibiting substrate‐dependent adhesion. The findings demonstrate competitive bonding performance and highlight the role of ionic interactions in tuning adhesion ...
Paula Bertolino Sanvezzo, Daniela Winsley Valereto Friozi, Vinícius de Oliveira, Marcia Cristina Branciforti   +3 more
wiley   +1 more source

Interfaces and Transport Phenomena in Materials Under Extreme Conditions. [PDF]

Materials (Basel)
Chen Y, Hu R, Wang H.
europepmc   +1 more source

Microstructural Evolution and Vacancy Defect Formation in Mn–Mo–Ni RPV Steel Under Low Cycle Fatigue: Insights From EBSD and PALS

Advanced Engineering Materials, EarlyView.
Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar, Dhanadeep Dutta, G. Bharat Reddy   +2 more
wiley   +1 more source