Results 181 to 190 of about 718,654 (353)

Method of temperature measurement in cutting zone while turning using portable class thermal imaging system [PDF]

, 2018
Ivan V. Anukhin, S. A. Lyubomudrov, V. I. Anukhin, N.V. Nikitkov   +3 more
openalex   +1 more source

A Thermodynamic 3D Model for the Simulation of Diffusion‐Controlled Alloying Processes in Heterogeneous Material Structures

Advanced Engineering Materials, EarlyView.
A numerical model resulting from irreversible thermodynamics for describing transport processes is introduced, focusing on thermodynamic activity gradients as the actual driving force for diffusion. Implemented in CUDA C++ and using CalPhaD methods for determining the necessary activity data, the model accurately simulates interdiffusion in aluminum ...
Ulrich Holländer, Leonhard Holländer, André Langohr, Hans Jürgen Maier   +3 more
wiley   +1 more source

EFFECT OF FEED RATEAND RACK ANGLE ON CUTTING FORCE AND GENERATED TEMPERATURE IN AN ORTHOGONAL TRUNING PROCESS

Diyala Journal of Engineering Sciences, 2015
In this research, a FEM simulation of orthogonal turning process is made. The effects of feed rate and rack angle of cutting tool on cutting force and generated temperature are analyzed. The analyses are curried out using MSC Marc 2013.
Zaid S. Hammoudi
doaj  

UPLC‑MS/MS‑based metabolomic characterization and comparison of pancreatic adenocarcinoma tissues using formalin‑fixed, paraffin‑embedded and optimal cutting temperature‑embedded materials. [PDF]

Int J Oncol, 2019
Feng D, Yuan J, Liu Q, Liu L, Zhang X, Wu Y, Qian Y, Chen L, Shi Y, Gu M.   +9 more
europepmc   +1 more source

EFFECTS OF TEMPERATURE AND STRAIN RATE OF DIFFICULT-TO-CUT PLATE ON ITS DEFORMATION BEHAVIOR UNDER CUTTING BY WEDGE AND SQUARE PUNCH.

, 2020
Cong Hanh Nguyen
openalex   +1 more source

Experimental Analysis of chip-back temperature during machining depending on cutting parameters

, 2015
Iosr Journals, Mangal Singh Sisodiya, Laxman Kumar Pandey, Amit Sharma   +3 more
openalex   +1 more source

Zein‐Based Adhesives: Sustainable Extraction and Application in Bioadhesive Technologies

Advanced Engineering Materials, EarlyView.
Zein is extracted from corn gluten meal using a simple and scalable process with high yield (~90%). The resulting protein is applied in bioadhesives modified with Ca2+ and Fe3+ ions, exhibiting substrate‐dependent adhesion. The findings demonstrate competitive bonding performance and highlight the role of ionic interactions in tuning adhesion ...
Paula Bertolino Sanvezzo, Daniela Winsley Valereto Friozi, Vinícius de Oliveira, Marcia Cristina Branciforti   +3 more
wiley   +1 more source

Dataset on flank wear, cutting force and cutting temperature assessment of austenitic stainless steel AISI316 under dry, wet and cryogenic during face milling operation. [PDF]

Data Brief, 2019
Rao KMC, Malghan RL, Herbert MA, Rao SS.
europepmc   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Effects of cryogenic cooling on cutting temperature and surface roughness in turning of AA7075 aluminum alloy. [PDF]

Sci Rep
Ranjbar S, Foorginejad A, Emam SM, Ebadi M, Shiri K.   +4 more
europepmc   +1 more source