Results 241 to 250 of about 900,172 (360)

The Influence of Contour Form Geometric Features and the Number of Cutting Passes on the Surface Quality Characteristics and Critical Points of Cutting Tools Fabricated by Wire Electrical Discharge Machining (WEDM). [PDF]

Micromachines (Basel)
Alinaghizadeh A, Azarhoushang B, Hadad M.   +2 more
europepmc   +1 more source

Research and Development of Hard Material for Cutting Tools

, 2016
Satoshi Kinoshita
openalex   +2 more sources

Characterization of Defect Distribution in an Additively Manufactured AlSi10Mg as a Function of Processing Parameters and Correlations with Extreme Value Statistics

Advanced Engineering Materials, EarlyView.
Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt, Varma Kvvssn, Hossein Laieghi, Zia Uddin, Peyman Ansari, E. Kıvanç Sadak, Can Barış Toprak, Hüseyin Kızıl, Enrico Salvati   +8 more
wiley   +1 more source

Theoretical and experimental study of cutting mechanics of graphite fiber reinforced preimpregnated composite (prepreg), and the effect of tool geometry on cutting quality and fibre deflection [PDF]

, 1995
Yuan Wang
openalex  

On the selection of cutting condition in machining cast-iron rolls - The relation between microstructure and tool wear.

, 1987
Ryozo Kitagawa
openalex   +2 more sources

Facilitating Expedited Drug Approval—the Past, Present, and Future of Clinical Trials for Pediatric Rheumatic Disease

Arthritis Care &Research, EarlyView.
Pamela F. Weiss, Hermine I. Brunner
wiley   +1 more source

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

Effect of Si₃N₄ Additive on Microstructure and Mechanical Properties of Ti(C,N)-Based Cermet Cutting Tools. [PDF]

Materials (Basel)
Elgazzar A, Zhou SJ, Ouyang JH, Peng ZJ, Yao JT, Liu ZG, Wang YJ, Wang YM.   +7 more
europepmc   +1 more source

Tool and Tool Guide Design for Shear Cutting of Tubes

, 2013
Yukio Kasuga, Masahiro Murakami, Shigehiro Kawamori   +2 more
openalex   +2 more sources

Carboxylic‐Acid Functionalized Multiwalled Carbon Nanotube‐Alkane‐Based Resistive Temperature Sensor for Cold Chain Applications

Advanced Engineering Materials, EarlyView.
This study presents a reversible temperature sensor with high switching ratio, ∼103. The device is fabricated using PET‐ITO and carbon nanotube dispersions in alkane. Considering its application in cold chain logistics, a proof‐of‐concept with LED is showcased. Thus, a temperature drop below the threshold temperature (crystallization temperature of the
Sunil Kumar Behera, Philippe Marrec, A. Jorge Parola, Madalena Dionísio, Hugo Águas, Andreia F. M. Santos, Hamed Pourkheirollah, Donald Lupo, César A. T. Laia   +8 more
wiley   +1 more source