Results 71 to 80 of about 8,653 (308)
Biomaterials Used in Injectable Implants (Liquid Embolics) for Percutaneous Filling of Vascular Spaces [PDF]
, 2018 The biomaterials currently used in injectable implants (liquid embolics) for minimally invasive image-guided treatment of vascular lesions undergo, once injected in situ, a phase transition based on a variety of physicochemical principles. The mechanisms
Doelker, Eric +2 more
core
Miniaturized Devices for On‐the‐Spot Generation of Small‐Diameter Vascular Grafts
Advanced Materials Technologies, EarlyView.An intracorporeal extrusion device is developed for on‐the‐spot generation of vascular grafts with tunable diameters spanning from 1 to 6 mm. The device uses biomimetic polymers and light, to promptly obtaining biocompatible and high‐burst pressure‐resistant grafts.
Deyanira Hernandez‐Sanchez +11 more
wiley +1 more source
Revista Cubana de Medicina General Integral, 2005 Se realizó un ensayo clínico para evaluar la efectividad y seguridad del adhesivo tisular Tisuacryl en el sellado de heridas cutáneas menores de 6 cm, tanto de origen traumático como quirúrgico.
Rosa Mayelín Guerra Bretaña +5 more
doaj
Poka: A Necro‐Robot Beetle with a Measured Payload Ratio of 6847%
Advanced Robotics Research, EarlyView.Here, Poka, a necro‐robot beetle with the ability to carry more than 68 times its own weight, is introduced, making it also a walking robot with the highest payload ratio measured to date. This paper is concerned with the design, manufacture and validation of ‘Poka', a novel millimetre‐scale necro‐robot aimed at bridging the performance gap between ...
Yordan Tsvetkov, Parvez Alam
wiley +1 more source
Structural and adhesion properties of poly(ethyl 2-cyanoacrylate) post-cured at different temperatures and times [PDF]
, 2019 The structure and properties of poly(ethyl 2-cyanoacrylate)s (pECNs) cured at 25 °C during 24 hours, and post-cured at different temperatures (45-90 °C) and times (2-6 hours) were studied.
Alonso, Diego A. +2 more
core +2 more sources
Advanced Science, EarlyView.Graphene‐PEDOT:PSS fillers revolutionize soft electronics by transforming jelly‐like materials into skin‐like systems with self‐healing, heat‐responsiveness, and multiplex sensing capabilities. This novel material exhibits exceptional printability, flexibility, and adhesiveness, enabling seamless integration into bioelectronics and tissue‐cyborganic ...
Morteza Alehosseini +7 more
wiley +1 more source
Molecules, 2005 A facile synthesis of 3-methylthio-3-arylamino-2-cyanoacrylates from 3,3-dimethylthioacrylate and aromatic amines or amino pyridines has been achieved in moderate to high yields (64.0% ~ 93.5%) in 30 minutes at 50°C under microwave irradiation.
Deyu Hu +6 more
doaj +1 more source
Advanced Science, EarlyView.A schematic diagram showing the OcuPair adhesive hydrogel formulation loaded into the final delivery device and applied over the full‐thickness corneal wound in an in vivo rabbit model of corneal injury followed by in situ crosslinking to form a transparent hydrogel bandage sealing the wound.
Siva P. Kambhampati +6 more
wiley +1 more source
Scalable substrate development for aqueous sample preparation for atom probe tomography
Journal of Microscopy, EarlyView., 2023 Abstract Reliable and consistent preparation of atom probe tomography (APT) specimens from aqueous and hydrated biological specimens remains a significant challenge. One particularly difficult process step is the use of a focused ion beam (FIB) instrument for preparing the required needle‐shaped specimen, typically involving a ‘lift‐out’ procedure of a
Eric V. Woods +4 more
wiley +1 more source
Production Engineering Archives, 2017 Adhesive bonding is one of the simplest and most common methods used for joining materials. It is applied in both production and repair works. The most commonly used adhesives are cyanoacrylates, due to the possibility of combining various materials and ...
Mazur Piotr
doaj +2 more sources