Results 91 to 100 of about 320,909 (283)

Modification of three-dimensional transition in the wake of a rotationally oscillating cylinder [PDF]

, 2010
A study of the flow past an oscillatory rotating cylinder has been conducted, where the frequency of oscillation has been matched to the natural frequency of the vortex street generated in the wake of a stationary cylinder, at Reynolds number 300.
Leontini, Justin S., Justin S. Leontini, Mark C. Thompson, Lo Jacono, David, Thompson, Mark C., John Sheridan, David Lo Jacono, Sheridan, John   +7 more
core   +1 more source

Superlubricity and Corrosion Inhibition Properties of Solvate Ionic Liquids in Hybrid Carbon Fiber Reinforced Plastic–Steel Interfaces

Advanced Engineering Materials, EarlyView.
Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees, Timothy Harte, Bhagya Dharmasiri, Y. Athulya Wickramasingha, David J. Hayne, Daniel J. Eyckens, Luke C. Henderson   +6 more
wiley   +1 more source

Discrepancies Between Micro Versus Macroscale Viscoelastic Properties in a Microplastic‐Tissue Composite Model

Advanced Engineering Materials, EarlyView.
This study explores the discrepancies between bulk mechanics and spatial mapping in a tissue‐mimetic hydrogel model. Microplastic particles create localized stiff mechanical microenvironments that are detectable by cellular‐scale nanoindentation but leave bulk properties unchanged as measured by rheology.
Ahron T. Verschleisser, Baptiste Le Roi, Omri Leshem, Joshua M. Grolman   +3 more
wiley   +1 more source

Three Cylinder Locomotives [PDF]

Journal of the Institution of Locomotive Engineers, 1918
n ...
openaire   +2 more sources

Simulation‐Based Analysis of Insert Pull‐Out in Nickel‐Polyurethane Hybrid Foams Using CT‐Derived Geometries

Advanced Engineering Materials, EarlyView.
CT‐based finite element simulations combined with in situ X‐ray computed tomography are used to analyze insert pull‐out in nickel‐coated polymer foams. Despite variations in material parameters, deformation consistently concentrates within a narrow annular region around the insert.
Yannik Bautz, Jonas Fell, Hendrik Jost, Stefan Diebels, Hans‐Georg Herrmann   +4 more
wiley   +1 more source

Comparative efficiency testing of a composite hydraulic cylinder

Aviation
The paper points to the increasing use of composite materials in hydraulic components. This entails many benefits, such as weight reduction which is particularly important in aviation. However, new problems arise with the use of new materials.
Michał Stosiak, Marek Lubecki, Michał Banaś   +2 more
doaj   +1 more source

Cylinder-Cylinder Attraction in Uniform Flow

Natural Science, 2018
Two cylinders in a uniform flow can attract each other when their separation distance is within the zones of the perturbed velocities of the cylinders. Enhanced perturbed velocity between cylinders causes lowered pressure by Bernoulli’s law. If the cylinders touch or the gap is very small, the flow will work to separate the cylinders.
openaire   +2 more sources

Design of a Multistable Finger Prosthesis with Programmable Metamaterials

Advanced Engineering Materials, EarlyView.
This research article shows the development of a multistable programmble metamaterial for the use as a finger prosthesis. The material was designed on different hierarchical levels where the influence of geometrical parameters and combination of mechanical elements was explored.
Franziska Wenz, Jannik Krohn, Alexander Leichner, Dilip Challisery, Heiko Andrae, Chris Eberl   +5 more
wiley   +1 more source

Effectiveness of kerosene/water conveying ternary (Cu–SiO2–Al2O3) nanoparticles flowing in vertical cylinder subjected to a melting phenomenon

Journal of Taibah University for Science
The circulation of ternary nanoparticles (Cu–SiO2–Al2O3) in a vertical cylinder filled with kerosene and water is important for improving the transmission of heat in modern lubricant and cooling technologies.
Javali Kotresh Madhukesh, Gosikere Kenchappa Ramesh   +1 more
doaj   +1 more source

Fabrication Routes for Ionic Conducting Fiber Strain Sensors

Advanced Engineering Materials, EarlyView.
Ionic conducting fiber strain sensors (ICFSs) offer compliant, textile‐integrable sensing. Thus far, the commercialization of ICFSs has been constrained by fiber fabrication routes. This review provides a fabrication‐centric analysis of ICFSs correlating processing strategies with material properties and scalability.
Leo John Kershaw, Zhanhong Yang, Anne Ladegaard Skov, Magdalena Skowyra   +3 more
wiley   +1 more source