Results 71 to 80 of about 1,183 (140)

Nanomaterials‐Decorated Biomass‐Derived Carbon for Overall Water Splitting: Interfacial Engineering, Mechanistic Insights, and Device Translation

The Chemical Record, Volume 26, Issue 8, August 2026.
Biomass‐derived carbon provides a sustainable, porous, and conductive scaffold that stabilizes nanomaterials for bifunctional hydrogen evolution reaction/oxygen evolution reaction catalysis. This review summarizes design strategies (defects, heteroatom doping, heterostructures, single atoms), mechanistic/density functional theory insights, degradation ...
Paricha Jebin, Md. Rakib Khan, Syed Shaheen Shah, S. M. Mostafa Kamal, Mst. Kaniz Subarna, Nipa Debnath, Md. Abdul Aziz, Bong‐Joong Kim, A. J. Saleh Ahammad   +8 more
wiley   +1 more source

Dynamical Characterization of Plates Containing Plane Cracks with Functional Gradient Materials. [PDF]

Materials (Basel)
Liu G, Xi A, Qi Y, Han W.
europepmc   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, Volume 28, Issue 14, 22 July 2026.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

Advanced Technologies for Characterizing and Detecting Battery Thermal Failure: A Review. [PDF]

Adv Sci (Weinh)
Chen Y, Sun Z, Zong W, Dai Y, Ng KL, Shearing PR.   +5 more
europepmc   +1 more source

Influence of Si Content and Milling Duration on the Microstructure and Mechanical–Tribological Properties of AlCoCrFeNiSi High‐Entropy Alloys

Advanced Engineering Materials, Volume 28, Issue 14, 22 July 2026.
Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş, Mehmet Emin Demir, Sercan Özpınar   +2 more
wiley   +1 more source

A Comparison of Discrete Crack and Smeared Crack Methods Applied to CFRP/Al Riveting Damage Modeling. [PDF]

Materials (Basel)
Zhang M, Tian K, Cao Z, Tay TE.
europepmc   +1 more source

Time and temperature dependence of residual stress evolution and protrusion behavior in through-glass vias. [PDF]

Microsyst Nanoeng
Wang H, Ma B, Liu P, Tian W, Liang H, Zhang X, Chen H, Lu G, Yang X.   +8 more
europepmc   +1 more source

The Influence of Fiber Tension and Filament Winding Patterns on the Strength of Thin-Walled Fiber-Reinforced Polymer Composite Tubes. [PDF]

Polymers (Basel)
Paczkowska K, Pacholec Z, Błażejewski W.   +2 more
europepmc   +1 more source

Effect of Thickness and Stitch Density on Low-Velocity Impact and Compression After Impact Properties of Stitched Composite Laminates. [PDF]

Polymers (Basel)
Liu B, Wang F, Zheng Y, Huang J, Jiang S, Zhang W.   +5 more
europepmc   +1 more source

Ballistic Performance of 7A52/7A62 Aluminum Alloy Laminates: A Numerical Investigation of Configuration Effect. [PDF]

Materials (Basel)
Wang Q, Yin M, Zhou J, Liu X, Zhang H, Mei R, Chen Z, Cao Y, Wang Q, Cong F, Zhang Y.   +10 more
europepmc   +1 more source