Results 111 to 120 of about 174,429 (312)
Nonlinear stability of two dusty magnetic liquids surrounded via a cylindrical surface: impact of mass and heat spread. [PDF]
Sci Rep, 2023 Moatimid GM, Mostafa DM.
europepmc +1 more source
Cylindrical-water-resonator-based ultra-broadband microwave absorber
, 2018 A cylindrical-water-resonator-based absorber with ultra-broad operating band at microwave band is demonstrated theoretically and experimentally for the first time. By utilizing dielectric resonator (DR) mode and spoof surface plasmon polariton (SPP) mode
Jia Yuan Yin (17491326) +1 more
core +1 more source
Advanced Engineering Materials, EarlyView.Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş +2 more
wiley +1 more source
, 2010 The conjecture of Tuinier (J. Colloid Interface Sci. 258 (2003) 45) for the electrical potentials near a cylindrical surface and near a spherical surface under the conditions of symmetric electrolyte and large scaled radius are derived by solving the ...
Lin, S. H.; Hsu, Jyh-ping; 曾琇瑱; Tseng, Shio-jenn; Chen, C. J.
core +1 more source
Simulation of Grinding Surface Creation – A Single Grit Approach [PDF]
, 2010 The paper presents an investigation of grinding material removal mechanism using finite element method. Understanding of grinding removal mechanism relies on the investigation of material removal by each individual grain.
Opoz, Tahsin Tecelli +3 more
core +1 more source
Advanced Engineering Materials, EarlyView.Grain boundary triple junctions are an essential ingredient of the microstructure of polycrystalline materials. In this study, a triple junction is observed using atomic‐resolution scanning transmission electron microscopy and characterized. Computer simulations reveal that the junction has a dislocation character that is determined by the joining ...
Tobias Brink +4 more
wiley +1 more source
, 2010 This paper describes an automated surface finishing system (ASFS) with in-process surface topography inspection. The acquired surface topography feedback is used to calculate the surface error and to generate the finishing paths for each level of surface
陳炤彰; Chen, Chao-chang A.; Duffie, Neil A.
core +1 more source
Spectral Domain Low- Coherence Interferometry for On-line Surface Inspection [PDF]
, 2013 We present an on-line surface measurement technique based on spectral domain low-coherence interferometry (SD-LCI), which can obtain a one dimensional surface profile with just one shot.
Gao, F. +5 more
core +1 more source
Design and Analysis of Compression–Torsion Coupling Metamaterials Using the Golden Section Method
Advanced Engineering Materials, EarlyView.A novel compression–torsion metamaterial is engineered using inclined rods and symmetry breaking. To optimize its torsional performance, the golden section method is employed. The mechanical response of the metamaterial is validated through both numerical analysis and experimental validation.
Amirhossein Hassani, Sara Bagherifard
wiley +1 more source
Active Corrosion Protection of Sintered AA7075 Aluminum Alloy via Mn Powder Addition
Advanced Engineering Materials, EarlyView.AA7075 containing Mn‐rich particles is fabricated via spark plasma sintering using AA7075 and Mn powders. Corrosion resistance is evaluated through dip‐and‐dry tests using 0.1 M NaCl (pH 6.0), and mass loss decreases with increasing Mn addition. Mn‐rich particles function as a source of Mn ions, and formation of Mn‐accumulation films on Cu‐containing ...
Ko Ebina, Masashi Nishimoto, Izumi Muto
wiley +1 more source