Results 1 to 10 of about 474 (181)

The Aplication of Vibro – Abrasive Machining for Smoothing of Castings

Archives of Foundry Engineering, 2017
The paper presents the production problems related to casting using precision casting methods. The essential adverse effect of the casting process is the presence of burrs understood as oversize material necessary to remove the next finishing operations.
Bańkowski D., Spadło S.
doaj   +1 more source

Sustainability Enhancement of a Turbine Vane Manufacturing Cell through Digital Simulation-Based Design

Energies, 2016
Modern manufacturing systems should satisfy emerging needs related to sustainable development. The design of sustainable manufacturing systems can be valuably supported by simulation, traditionally employed mainly for time and cost reduction.
Alessandra Caggiano, Adelaide Marzano, Roberto Teti   +2 more
doaj   +1 more source

MODULAR EQUIPMENT FOR ELECTROCHEMICAL DEBURRING

Nonconventional Technologies Review, 2020
The paper deals with the development of a prototype modular equipment for electrochemical deburring to be used in case of small and medium size workpieces that can be machined just on the worktable of the equipment, but mainly in case of large parts ...
Gabriela Marina Ene, Alexandra Daniela Coțofană, Liviu Daniel Ghiculescu   +2 more
doaj  

Low-Cycle Fatigue Properties of the X70 High-Frequency Electric-Resistant Welded Pipes

Advances in Materials Science and Engineering, 2018
The strength, toughness, corrosion, and fatigue resistance are the main requirements for evaluating the integrity of a pipeline. In this study, the tensile strength, impact toughness, and fatigue properties of the pipe body and weld joint of an X70 high ...
Peng Tian, Kai Xu, Guang-ping Lu, Gui-ying Qiao, Fu-ren Xiao   +4 more
doaj   +1 more source

Provision of Rational Parameters for the Turning Mode of Small-Sized Parts Made of the 29 NK Alloy and Beryllium Bronze for Subsequent Thermal Pulse Deburring. [PDF]

Materials (Basel), 2023
Martyushev NV, Bublik DA, Kukartsev VV, Tynchenko VS, Klyuev RV, Tynchenko YA, Karlina YI.   +6 more
europepmc   +1 more source

Research on sodium bicarbonate abrasive jet machining technology for post-processing treatments of 3D printed PEEK implant to achieve non-destructive deburring and enhancing cell adhesion

Advanced Industrial and Engineering Polymer Research
The non-destructive deburring and hydrophilic surface machining of 3D printed Polyetheretherketone (PEEK) implants surface is critical for post-processing production of the implants.
Zhouyu Jiang, João Pedro Oliveira, Yuchen Zhang, Lei Liu, Jiajia Shen, Wenhao Su, Zihui Jing, Mingliang Wang   +7 more
doaj   +1 more source

Economic tradeoffs in deburring [PDF]

, 1976
The reliability of small precision mechanisms depends on the production of burr-free, sharp-edged parts. An investigation was conducted to determine how these requirements could best be maintained. The study included investigating the capabilities of the 24 major deburring processes and finding other techniques for minimizing burr-related problems and ...
openaire   +2 more sources

Optimization of Titanium Alloy Drilling to Minimize the Secondary Burr after Deburring Process. [PDF]

Materials (Basel), 2022
Franczyk E, Zębala W.
europepmc   +1 more source

Thermal Pulse Processing of Blanks of Small-Sized Parts Made of Beryllium Bronze and 29 NK Alloy. [PDF]

Materials (Basel), 2022
Isametova ME, Martyushev NV, Karlina YI, Kononenko RV, Skeeba VY, Absadykov BN.   +5 more
europepmc   +1 more source

Single-Step Drilling Using Novel Modified Drill Bits Under Dry, Water, and Kerosene Conditions and Optimization of Process Parameters via MOGA-ANN and RSM

Lubricants
The burr removal and finishing of drilled hole walls typically require multiple post-processing steps. This experimental study introduces a novel single-step drilling approach using modified drill bits for simultaneous burr removal and surface finishing ...
Sumitava Paul, Barun Haldar, Hillol Joardar, Nripen Mondal, Naser A. Alsaleh, Maaz Akhtar   +5 more
doaj   +1 more source