Results 31 to 40 of about 323 (224)
Analysis and implementation of veneer production waste in order to design decorative wall panels
Rethinking Buildings and Materials for a Sustainable Future : book of abstracts, 2022 Increasing concern for the preservation of the environment aims to reduce natural changes, which ultimately causes greater social changes. As social changes occur, so do changes in the professional approach in the field of technology, production, and design. It is very important nowadays to rethink technology and processes in order to reduce production
Mamić, Domagoj +4 more
openaire +2 more sources
Speculating on (the) urban (of) art: (un)siting street art in the age of neoliberal urbanisation [PDF]
Horizontes AntropológicosThis paper addresses the current co-optation of street art into an uncritical aesthetic supplement to the process of neoliberal urbanisation, by focusing on its unresolved relation with its own site. This is done in three steps.
Andrea Pavoni
doaj +2 more sources
Wood Veneer Dyeing Enhancement by Ultrasonic-assisted Treatment
BioResources, 2015 To extend the potential application of ultrasonic treatment in dyeing low-quality wood to improve decorative value, wood veneers were dyed with an ultrasonic assisted dyeing system.
Yi Liu +6 more
doaj +1 more source
Annals of Clinical and Translational Neurology, EarlyView.ABSTRACT Objective Facioscapulohumeral muscular dystrophy (FSHD) is one of the most debilitating and common muscular dystrophies. Despite its severity, no approved therapy exists for FSHD patients. However, several therapeutic candidates are currently under development, and some have recently entered clinical trials, marking the need for reliable ...
Mustafa Bilal Bayazit +11 more
wiley +1 more source
Arthritis Care &Research, EarlyView.Objective This research article aims to describe the prevalence, associations, and health‐related quality of life (HRQoL) impact of mucocutaneous features of systemic lupus erythematosus (SLE). Methods Data from the Asia‐Pacific Lupus Collaboration cohort were analyzed (2013–2021).
Amanda M. Saracino +42 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
ANATOMI TUJUH JENIS KAYU DARI MALUKU UTARA (Anatomy of Seven Wood Species from North Maluku)
Jurnal Penelitian Hasil Hutan (Journal of Forest Products Research), 2017 Gross and anatomical fentures of seven wood species from North Maluku were observed and described for identification purposes. Fibre dimension were also measured and evaluated for their suitability for pulp and paper. The colour of wood ranges from
Y I Mandang
doaj +1 more source
Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys
Advanced Engineering Materials, EarlyView.Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Knowledge‐based atomistic workflows are presented for mechanical and thermodynamic properties. By coupling modular simulations with ontology‐aligned metadata and provenance, Fe case studies on elastic behavior, defects, thermal properties, and Hall–Petch strengthening reveal how FAIR, queryable, and reusable simulation data can be generated. Mechanical
Abril Azócar Guzmán +5 more
wiley +1 more source
About the quality and longevity of facing of laminose stone walls [PDF]
Инженерно-строительный журнал, 2011 External wall enclosure of frame buildings is usually carried out in the form of sandwich laying, with protectively-decorative brick facing and inside layer made of aerocrete or foam concrete blocks, or slot-hole ceramic stones which fill he space ...
R.B. Orlovich, V.N. Derkach
doaj