Results 151 to 160 of about 559,258 (294)

Manufacturing Continuous Fiber‐Reinforced Printing Filaments: Development of a Post‐Consolidation Unit

Advanced Engineering Materials, EarlyView.
A novel, temperature‐controlled post‐consolidation unit is developed to test its potential to improve the melt impregnation process used to manufacture continuous fiber‐reinforced filaments for additive manufacturing of high‐performance thermoplastics.
Daniel Beermann, Patrick Schiebel, David May   +2 more
wiley   +1 more source

TCQI-YOLOv5: A Terminal Crimping Quality Defect Detection Network. [PDF]

Sensors (Basel)
Yu Y, Ren D, Meng L.
europepmc   +1 more source

Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6

Advanced Engineering Materials, EarlyView.
The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter, Thomas Wegener, Andreas Schilling, Martin Fehlbier, Thomas Niendorf   +4 more
wiley   +1 more source

Lightweight DETR algorithm for X-ray weld defect detection. [PDF]

Sci Rep
Zhang X, Chen H, Liu Z, Anli S.
europepmc   +1 more source

Design and Prototyping of Topology‐Optimized, Additively Manufactured Lightweight Components for Space Robotic Systems: A Case Study

Advanced Engineering Materials, EarlyView.
The results demonstrate a simulation‐driven workflow that applies LSB topology optimization with additive manufacturing constraints to mission‐specific load cases, integrating European Cooperation for Space Standardization compliant verification and manufacturability to develop structurally efficient rover suspension components.
Stelios K. Georgantzinos, Grigorios Kostopoulos, Eleni Papadopoulou, Stefanos Voulgaris, Alexandra Tseni, Panteleimon Bakalis, Maria N. Gkara, Chara Ch. Mitropoulou, Georgios Kazakis, Alin Munteanu, Jeremi Gancet, Nikos D. Lagaros   +11 more
wiley   +1 more source

Deep Learning-Based 3D Reconstruction for Defect Detection in Shipbuilding Sub-Assemblies. [PDF]

Sensors (Basel)
Arcano-Bea P, García-Fischer A, Gómez-González PP, Zayas-Gato F, Calvo-Rolle JL, Quintián H.   +5 more
europepmc   +1 more source

Nitride‐Reinforced Metal Matrix Nanocomposite Powders Production by Plasma‐Assisted Thermochemical Treatment of Intermetallic Powders

Advanced Engineering Materials, EarlyView.
This study proposes a new methodology for producing metal matrix nanocomposites in the solid state. The process involves the plasma‐assisted thermochemical treatment of metallic alloy powders. As a proof‐of‐concept, TiN nanoparticles are synthesized directly on the surface of FeTi intermetallic powder particles, enabling the development of the ...
Deivison Daros Paim, Antônio Rogério de Souza, Tatiana Bendo, Aloisio Nelmo Klein, Rodrigo Perito Cardoso   +4 more
wiley   +1 more source

Wafer Defect Detection Technology Based on CTM-IYOLOv10 Network. [PDF]

J Imaging
Ji P, He Z, Yang W, Du J, Ye G, Lu X.
europepmc   +1 more source

Screen‐Printed Flexible Piezoelectric Force Sensor Array with Electromagnetic Interference Shielding

Advanced Engineering Materials, EarlyView.
This article introduces a flexible screen‐printed piezoelectric sensor array designed for low‐frequency healthcare applications such as tactile sensing and cardiovascular monitoring. The device integrates interface electronics enabling the simultaneous acquisition of up to 128 signals, along with flexible EMI shielding that significantly reduces noise ...
Joseph Faudou, Mohammed Benwadih, Arnaud Gabas, Lina Kadura, Minh‐Quyen Le, Daniel Grinberg, Pierre‐Jean Cottinet   +6 more
wiley   +1 more source

Research on metal surface defect detection method based on deep learning. [PDF]

Sci Rep
Feng Y, Sun G, Zhao Y, Wang F, Yu X, Guo X, Chen X.   +6 more
europepmc   +1 more source