Results 211 to 220 of about 37,150 (311)

Polarization increases nuclear stiffness in macrophages despite reduction in lamin A/C levels. [PDF]

NPJ Biol Phys Mech
Elpers MA, Odell J, Henretta SJ, Shu T, Ambekar YS, Saadi H, Woodworth GF, Zipfel WR, Scarcelli G, Holt LJ, Lammerding J.   +10 more
europepmc   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Rheological and biochemical comparison of cord and adult blood red cells for transfusion applications. [PDF]

Sci Rep
Mykhailova L, Vercellati C, Montemurro T, Zaninoni A, Marcello A, Fermo E, Cherubini A, Cimoni S, Bianchi P, Prati D, Villa S.   +10 more
europepmc   +1 more source

Advanced Electron Microscopy and Microcomputed Tomography Analysis of Single‐Crystal Ni‐Base Superalloys After Short‐Term Multiaxial Creep

Advanced Engineering Materials, EarlyView.
This work studies the anisotropic behavior of circular notched tensile specimens of Ni‐base superalloy single crystals during high‐temperature tensile creep along [001], [110], and [111]. Correlative scale‐bridging imaging of specimens reveals early rupture along [110] because 1) plastic deformation proceeds faster at notch center; 2) more (brittle ...
Leonardo Agudo Jácome, Lijie Cao, Christoph Somsen, Johannes Boes, René Hesse, Werner Theisen, Gunther Eggeler   +6 more
wiley   +1 more source

Modulatory effects of 6-Gingerol on erythrocyte deformability and morphology following lower extremity skeletal muscle ischemia-reperfusion injury in rats. [PDF]

Sci Rep
Özdem T, Kartal H, Çomu FM, Demirdaş E, Yavuz B, Ertaş E, Erol G, Demirkıran T, Kaymak Ş, Özdaş ME, Taşöz Özdaş I, Tokgöz Y, Özdemir VC.   +12 more
europepmc   +1 more source

Defect Evolution and Mechanical Performance of Fused Filament Fabrication‐Manufactured 17‐4PH Stainless Steel Revealed by X‐Ray Computed Tomography

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky, Márk Sárközi, Ibolya Zsoldos, Zoltán Weltsch   +3 more
wiley   +1 more source

Investigation of Red Blood Cell Properties on Impedance Signatures Generated in a Coulter Counter. [PDF]

Int J Numer Method Biomed Eng
Pottier P, Taraconat P, Gineys JP, Isèbe D, Nicoud F, Mendez S.   +5 more
europepmc   +1 more source

Electrified Damage in Motion Systems

Advanced Engineering Materials, EarlyView.
The electrified damage in motion systems is a fundamental framework presenting the degradation pathway arising from the coupling of electrical energy transport with mechanical contact and interfacial chemistry. The framework positions electrified damage as a distinct degradation regime with unique characteristic surface morphologies and failures of ...
M. Humaun Kabir, Angelina Nguyen, Hong Liang   +2 more
wiley   +1 more source

Recover aged/damaged erythrocytes and prevent them from aging by remodeling or enhancing their vital proteins: Hb and B3p. [PDF]

Front Cell Dev Biol
Jiang GY, Tuo WW, Wang Z, Chen XY, Huang YX.   +4 more
europepmc   +1 more source

Design and Analysis of Compression–Torsion Coupling Metamaterials Using the Golden Section Method

Advanced Engineering Materials, EarlyView.
A novel compression–torsion metamaterial is engineered using inclined rods and symmetry breaking. To optimize its torsional performance, the golden section method is employed. The mechanical response of the metamaterial is validated through both numerical analysis and experimental validation.
Amirhossein Hassani, Sara Bagherifard
wiley   +1 more source