Results 61 to 70 of about 102,126 (216)

Fabrication Routes for Ionic Conducting Fiber Strain Sensors

Advanced Engineering Materials, EarlyView.
Ionic conducting fiber strain sensors (ICFSs) offer compliant, textile‐integrable sensing. Thus far, the commercialization of ICFSs has been constrained by fiber fabrication routes. This review provides a fabrication‐centric analysis of ICFSs correlating processing strategies with material properties and scalability.
Leo John Kershaw, Zhanhong Yang, Anne Ladegaard Skov, Magdalena Skowyra   +3 more
wiley   +1 more source

Influence of TiC and TiN Ceramic Reinforcements on the Microstructure, Thermal Expansion Behavior, and Tensile Properties of Invar 36 Manufactured by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
This study examines Invar composites reinforced with titanium carbide (TiC) and titanium nitride (TiN) using laser powder bed fusion (LPBF). It presents the influence of reinforcements on microstructure, tensile properties, and thermal expansion. Results show that TiC effectively strengthens Invar while maintaining low thermal expansion, whereas TiN ...
Ayodeji Nathaniel Oyedeji, Natasha Sacks, Johannes Pötschke, Björn Matthey   +3 more
wiley   +1 more source

EVALUATION OF STRENGTH IN PRE-DEFORMED AUSTENITIC STAINLESS STEEL USING NONLINEAR ULTRASONIC WAVE

Jixie qiangdu, 2017
The different strengths induced by the different deformation modes for 304 austenitic stainless specimens were measured by using nonlinear ultrasonic wave technique.
ZHANG JianFeng, XUAN FuZhen
doaj  

Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning

Advanced Engineering Materials, EarlyView.
The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley   +1 more source

Deformation strength characteristics of unsaturated remoulded loess simulated by BBM model

Yantu gongcheng xuebao
The BBM model for unsaturated soils is analyzed, studied and validated. A modification is further made to the BBM model, so that the model is more consistent with the variation of matric suction in unsaturated loess.
ZHENG Fang 1, 2, SHAO Shengjun 3, 4
doaj   +1 more source

Gallium Microalloying in Bi–Sn Solders: Interfacial Phase Formation, Wettability, and Long‐Term Shear Reliability Under Isothermal Aging

Advanced Engineering Materials, EarlyView.
Gallium microalloying redirects interfacial reactions in low‐temperature Bi–Sn solders from Cu–Sn toward Cu–Ga intermetallic formation. The resulting Cu–Ga layer suppresses intermetallic growth during thermal aging, alters fracture pathways, and improves interfacial stability.
Iva Králová, Markéta Klimtová, Mohd Faizul Mohd Sabri, Yew Hoong Wong, Petr Veselý, Martin Plaček, Karel Dušek   +6 more
wiley   +1 more source

DEM-FDM investigation of bedding plane properties’ impact on laminated roof stability

Scientific Reports
Laminated roofs are susceptible to cutter roof failure caused by excavation disturbances. To assess the impact of bedding plane properties on their stability under mining stress, a panel-scale numerical model was created using a combination of the ...
Xiang Ma, Qingwen Shi, Brijes Mishra, Yun Zhao, Zhenhua Ouyang, Zhengjun Guo, Jiayang Wang   +6 more
doaj   +1 more source

Feasibility and Limitations of the Advanced Replica Process for Bioactive Glasses

Advanced Engineering Materials, EarlyView.
Periodic 3D‐printed Kelvin‐cell templates enable a controlled advanced replica process for fabricating highly porous glass lattices. Across P45K9, 45S5, and 13–93, material‐dependent differences in coating, burnout, and shrinkage lead to distinct strut morphologies, while comparable final porosities of 83%–88% are retained.
Swantje Funk, Elisabeth Keck, Alberto López‐Grande, Delia S. Brauer, Tobias Fey   +4 more
wiley   +1 more source

Theoretical strength and homogeneous sliding in metallic glass: exactly solvable model

Journal of the Mechanical Behavior of Materials, 2013
At low temperature, T→0, the yield stress of a perfect crystal is equal to its so-called theoretical strength. The yield stress of nonperfect crystals is controlled by the stress threshold of dislocation mobility.
Lazarev Nikolai, Bakai Alexander
doaj   +1 more source

High‐Entropy Alloy Interlayers Toward Advanced Joining for High‐Performance Structural Applications: Current Progress and Emerging Challenges

Advanced Engineering Materials, EarlyView.
HEA interlayers offer a versatile route for joining high‐performance structural materials. Their compositional and structural design regulates interfacial reactions, suppresses brittle IMCs, and improves metallurgical bonding. Sandwich interlayers further integrate defect healing with precipitation strengthening, enabling improved strength–ductility ...
Lin Yuan, Jiafen Song, Jinglong Li, Jiangtao Xiong, Tao Yang   +4 more
wiley   +1 more source