Results 161 to 170 of about 1,855,299 (332)

High‐Entropy Alloy Design Toward Cobalt Substitution for High Hardness and Low Wear Rate Using X–Cr–Fe–Mn–Ni System

Advanced Engineering Materials, EarlyView.
This study explores the replacement of cobalt using the high‐entropy alloy design strategy for wear‐resistant components operating at high temperatures. Starting from the Cantor alloy, cobalt is substituted with Cu, Al, V, or Mo. Metallurgical and tribological analyses reveal that aluminum, vanadium, and molybdenum effectively strengthen the developed ...
Rafaël Jénot, Laurent Peltier, Fodil Meraghni, Mathieu Marquer, Oriane Baulin, Clotilde Macke‐Bart   +5 more
wiley   +1 more source

Principle and Experimental Validation of a new Apparatus Allowing Large Deformation in Pure Bending: Application to thin Wire

, 2015
Gabriel Antherieu, Nathanaël Connesson, Denis Favier, Pierre Mozer, Yohan Payan   +4 more
openalex   +2 more sources

Microstructural Evolution and Mechanical Performance of Plasma‐Assisted Hybrid Friction Stir Welded Dissimilar Aluminum–Copper Joints

Advanced Engineering Materials, EarlyView.
Plasma‐assisted hybrid friction stir welding of dissimilar AlCu joints employs localized plasma preheating to balance heat input and enhance plastic flow. The optimized process reduces axial force by up to 35%, refines the microstructure, and achieves ≈96% joint efficiency.
Deepak Kumar Yaduwanshi, Pankaj Shrivastava, Ganesh Chouhan, Velaphi Msomi   +3 more
wiley   +1 more source

Deformation mechanisms of a rapidly solidified Al-8.8Fe-3.7Ce alloy [PDF]

, 1989
D. Legzdina, Triplicane A. Parthasarathy
openalex   +1 more source

Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6

Advanced Engineering Materials, EarlyView.
The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter, Thomas Wegener, Andreas Schilling, Martin Fehlbier, Thomas Niendorf   +4 more
wiley   +1 more source

Can Ti‐Based MXenes Serve as Solid Lubricants for Brake Applications? A Tribological Study

Advanced Engineering Materials, EarlyView.
This study explores the first implementation of Ti‐based MXenes materials in brake pad friction composite material. The resulting composite material exhibits a 48% reduction in the wear rate; alongside significant improvements are observed for thermal and mechanical properties.
Eslam Mahmoud, Jakob Gruber, Hakan Göçerler, Pierluigi Bilotto, Christian Gierl‐Mayer, Elham Loni, Michael Naguib, Carsten Gachot   +7 more
wiley   +1 more source

PLASTIC DEFORMATION AND ELECTRONIC MECHANISMS IN SEMICONDUCTORS AND INSULATORS

, 1981
P. B. Hirsch
openalex   +2 more sources

Design and Prototyping of Topology‐Optimized, Additively Manufactured Lightweight Components for Space Robotic Systems: A Case Study

Advanced Engineering Materials, EarlyView.
The results demonstrate a simulation‐driven workflow that applies LSB topology optimization with additive manufacturing constraints to mission‐specific load cases, integrating European Cooperation for Space Standardization compliant verification and manufacturability to develop structurally efficient rover suspension components.
Stelios K. Georgantzinos, Grigorios Kostopoulos, Eleni Papadopoulou, Stefanos Voulgaris, Alexandra Tseni, Panteleimon Bakalis, Maria N. Gkara, Chara Ch. Mitropoulou, Georgios Kazakis, Alin Munteanu, Jeremi Gancet, Nikos D. Lagaros   +11 more
wiley   +1 more source

Full-process deformation monitoring and failure characteristics analysis of damaged coal under 3D laser scanning technology. [PDF]

Sci Rep
Jiang P, Liu Y, Li G.
europepmc   +1 more source

NFDI MatWerk Ontology (MWO): A BFO‐Compliant Ontology for Research Data Management in Materials Science and Engineering

Advanced Engineering Materials, EarlyView.
This article presents the NFDI‐MatWerk Ontology (MWO), a Basic Formal Ontology‐based framework for interoperable research data management in materials science and engineering (MSE). Covering consortium structures, research data management resources, services, and instruments, MWO enables semantic integration, Findable, Accessible, Interoperable, and ...
Hossein Beygi Nasrabadi, Ebrahim Norouzi, Kostiantyn Hubaiev, Jörg Waitelonis, Harald Sack   +4 more
wiley   +1 more source