Results 101 to 110 of about 24,619,547 (331)
Evidence for postseismic deformation of the lower crust following the 2004 Mw6.0 Parkfield earthquake [PDF]
, 2011 Previous studies have shown that postseismic relaxation following the 2004 Mw6.0 Parkfield, CA, earthquake is dominated by afterslip. However, we show that some fraction of the afterslip inferred from kinematic inversion to have occurred immediately ...
Avouac, Jean-Philippe +2 more
core
Advanced Engineering Materials, Volume 27, Issue 6, March 2025.ErB4 and NdB4 nanostructured powders are produced by mechanochemical synthesis. 5 h mechanical alloying and 4 M HCl acid leaching are used in the production. ErB4 and NdB4 powders exhibit maximum magnetization of 0.4726 emu g−1 accompanied with an antiferromagnetic‐to‐paramagnetic phase transition at about TN = 18 K and 0.132 emu g−1 with a maximum at ...
Burçak Boztemur +5 more
wiley +1 more source
Geodetski Vestnik, 2013 At each point of the geodetic network, kinematic quantities are considered: normal strain, shear strain and rotation. This differs from the treatment of deformations on the basis of point movements as the traditional geodetic approach.
Aleš Marjetič
doaj +1 more source
On the E10/Massive Type IIA Supergravity Correspondence
, 2009 In this paper we investigate in detail the correspondence between E10 and Romans' massive deformation of type IIA supergravity. We analyse the dynamics of a non-linear sigma model for a spinning particle on the coset space E10/K(E10) and show that it ...
Henneaux, Marc +3 more
core +3 more sources
Advanced Engineering Materials, Volume 27, Issue 6, March 2025.The stability criteria affecting the formation of high‐entropy alloys, particularly focusing in supersaturated solid solutions produced by mechanical alloying, are analyzed. Criteria based on Hume–Rothery rules are distinguished from those derived from thermodynamic relations. The formers are generally applicable to mechanically alloyed samples.
Javier S. Blázquez +5 more
wiley +1 more source
Prediction of sheet necking with shell finite element models [PDF]
, 2003 In sheet forming simulations, the prediction of localised necking is an important goal. A pragmatic\ud approach is to compare calculated principal strains with a forming limit curve (FLC).
Boogaard, A.H. van den, Huetink, J.
core +1 more source
Bistable Mechanisms 3D Printing for Mechanically Programmable Vibration Control
Advanced Engineering Materials, EarlyView.This work introduces a 3D‐printed bistable mechanism integrated into tuned mass dampers (TMDs) for mechanically adaptive passive vibration suppression. Through optimized geometry, the bistable design provides adaptable vibration reduction across a broad range of scenarios, achieving effective vibration mitigation without complex controls or external ...
Ali Zolfagharian +4 more
wiley +1 more source
Elasto-plastic impact of hemispherical shell impacting on hard rigid sphere [PDF]
An analysis of plastic stress waves for cylindrical metallic projectile in impact is extended to an analysis of a hemispherical shell suffereing plastic deformation during the process of impact.
Raftopoulos, D. D., Spicer, A. L.
core +1 more source
Advanced Engineering Materials, EarlyView.Laser surface texturing significantly improves the corrosion resistance and mechanical strength of 3D‐printed iron polylactic acid (Ir‐PLA) for marine applications. Optimal laser parameters reduce corrosion by 80% and enhance tensile strength by 25% and ductility by 15%.
Mohammad Rezayat +6 more
wiley +1 more source
Deformation Analysis of the Rock Surrounding a Tunnel Excavated through a Gently Dipping Bed [PDF]
, 2022 Zhen Gao, Jianjun Luo, Xu Wu, Ke Li
openalex +1 more source