Results 41 to 50 of about 39,160 (287)
Advanced Engineering Materials, EarlyView.Laser surface texturing significantly improves the corrosion resistance and mechanical strength of 3D‐printed iron polylactic acid (Ir‐PLA) for marine applications. Optimal laser parameters reduce corrosion by 80% and enhance tensile strength by 25% and ductility by 15%.
Mohammad Rezayat +6 more
wiley +1 more source
X‐Ray Tomography Analysis of Damage Mechanisms in Metal Matrix Syntactic Foams During Compression
Advanced Engineering Materials, EarlyView.In situ synchrotron X‐ray tomography is used to investigate the internal damage mechanisms of AlSi12 metal matrix syntactic foam with ceramic hollow spheres during compressive loading. It is concluded that a homogeneous distribution of the second‐phase filler material results in a sequential collapse in a localized region; this leads to controlled and ...
Indrajeet Tambe +8 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study reports the fabrication of trabecular bioactive glass scaffolds (composition “1d”: 46.1SiO2‐28.7CaO‐8.8MgO‐6.2P2O5‐5.7CaF2‐4.5Na2O wt%) through vat photopolymerization and the relevant results from mechanical testing and in vivo implantation procedures in rabbit femora, showing great promise for bone tissue engineering applications.
Dilshat Tulyaganov +8 more
wiley +1 more source
Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6
Advanced Engineering Materials, EarlyView.The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter +4 more
wiley +1 more source
International Journal of Aerospace Engineering, 2018 The inverse finite element method (iFEM) for the 3D framework deformation reconstruction was introduced. As the process of iFEM did not require a priori knowledge, such as the modal shape, the loading, and the elastic-inertial material information of the
Yong Zhao, Jingli Du, Hong Bao, Qian Xu
doaj +1 more source
Micromachines, 2023 The position and altitude of a sub-reflector have an important influence on the pointing accuracy of a radio telescope. With the increase of the antenna aperture, the stiffness of the support structure for the sub-reflector decreases.
Qian Xu, Hong Bao
doaj +1 more source
Advanced Engineering Materials, EarlyView.The results demonstrate a simulation‐driven workflow that applies LSB topology optimization with additive manufacturing constraints to mission‐specific load cases, integrating European Cooperation for Space Standardization compliant verification and manufacturability to develop structurally efficient rover suspension components.
Stelios K. Georgantzinos +11 more
wiley +1 more source
A 3-D Surface Reconstruction with Shadow Processing for Optical Tactile Sensors
Sensors, 2018 An optical tactile sensor technique with 3-dimension (3-D) surface reconstruction is proposed for robotic fingers. The hardware of the tactile sensor consists of a surface deformation sensing layer, an image sensor and four individually controlled ...
Hanjun Jiang +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.A two‐step approach combining laser powder bed fusion of FeSi electrical steel with Bakelite infiltration enables the fabrication of multifunctional gyroid lattice composites. The resulting structures exhibit high strength, magnetic anisotropy, and complete polymer infiltration, demonstrating a simple and scalable route toward lightweight, mechanically
Angelo F. Andreoli +9 more
wiley +1 more source
Applied SciencesStructural monitoring is crucial for assessing structural health, and high-precision deformation prediction can provide early warnings for safety monitoring.
Houzeng Han +5 more
doaj +1 more source