Results 191 to 200 of about 495,366 (291)

The Bending Impact of the Failure Investigation of the Polymer-Reinforced Composite Protection Bars. [PDF]

Polymers (Basel)
Yilmazcoban IK.
europepmc   +1 more source

Enhanced Strength and Corrosion Resistance of Ti‐13Nb‐12Ta‐10Zr‐4Sn Alloy by Aging Treatment

Advanced Engineering Materials, EarlyView.
This work systematically investigates the effect of aging treatment on mechanical properties and corrosion behavior of vacuum arc‐melted Ti‐13Nb‐12Ta‐10Zr‐4Sn alloy. Owing to the increased α″ martensite, strength and corrosion resistance were significantly enhanced by aging treatment.
Yuhua Li, Rong Zhao, Qian Zhang, Haojie Wang, Yujing Liu, Lai‐Chang Zhang   +5 more
wiley   +1 more source

Structural dynamics and neural representation of wing deformation. [PDF]

Proc Natl Acad Sci U S A
Yarger AM, Maeda M, Siwanowicz I, Kajiyama H, Walker SM, Bomphrey RJ, Lin HT.   +6 more
europepmc   +1 more source

Bioinspired Shape‐Memory Hook Fasteners With Programmable Interlocking and Silent Release

Advanced Engineering Materials, EarlyView.
Bioinspired hook fasteners made from epoxy shape‐memory polymers are shown to switch between strong, secure attachment and gentle, silent release when heated. By combining programmable geometry and material response, these adaptive fasteners outperform commercial systems in strength and noise control, enabling new solutions for robotics, medical ...
Maria I. Vallejo Ciro, Manuel J. Carvajal Loaiza, Rahaf Homssi, Vanessa Restrepo   +3 more
wiley   +1 more source

Mechanical annealing in a soft granular layer under cyclic shear at varying frequencies. [PDF]

Sci Rep
Tapia-Ignacio C, Fossion RYM, López-González F.   +2 more
europepmc   +1 more source

Evaluation of Plasticity and Creep Parameters From Tensile Stress–Strain Data for a Range of Strain Rates

Advanced Engineering Materials, EarlyView.
This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley   +1 more source

Evaluation of Bending Deformations in Slender Cylindrical Structures Using Distributed Optical Fibre Strain Sensing. [PDF]

Sensors (Basel)
Herath M, Ivanov OV, Bhavsar K, Gilbert JM.   +3 more
europepmc   +1 more source

Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants

Advanced Engineering Materials, EarlyView.
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir, Jixing Lin, Yuncang Li, Li Zhu, Paul F. A. Wright, Cuie Wen   +5 more
wiley   +1 more source

Radiation-pressure-induced surface deformation of transparent liquids due to laser beams under oblique incidence. [PDF]

Photoacoustics
Anghinoni B, Malacarne LC, Jacinto C, Baesso ML, Lendl B, Astrath NGC.   +5 more
europepmc   +1 more source

In Situ Micromechanical Study of Bimodal γ′–γ″ Precipitate Assemblies in Ni–Cr–Al–Nb Superalloy

Advanced Engineering Materials, EarlyView.
A Ni–Cr–Al–Nb superalloy with a bimodal γ′–γ″ precipitate distribution is developed. Composite precipitate assemblies form through heterogeneous nucleation, effectively impeding dislocation motion. Micropillar compression reveals high strength at room and elevated temperatures, governed by precipitate shearing, with coupled faulting mechanisms ...
Ujjval Bansal, Tae‐Hyeok Kang, Pyuck‐Pa Choi, Subin Lee, Christoph Kirchlechner   +4 more
wiley   +1 more source