Results 41 to 50 of about 100,713 (258)
Nonaqueous Fluoride/Chloride Anion-Promoted Delamination of Layered Zeolite Precursors: Synthesis and Characterization of UCB-2 [PDF]
, 2011 The delamination of layered zeolite precursor PREFER is demonstrated under mild nonaqueous conditions using a mixture of cetyltrimethylammonium bromide, tetrabutylammonium fluoride, and tetrabutylammonium chloride in N,N-dimethylformamide (DMF) as ...
Eilertsen, Einar A. +6 more
core +1 more source
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source
A study of composite material damage induced by laser shock waves [PDF]
, 2013 A laser shock wave technique has been used to study the damage tolerance of T800/M21 CFRP (Carbon Fiber Reinforced Polymer) composite material with different lay_ups.
BERTHE, Laurent +7 more
core +5 more sources
Advanced Engineering Materials, EarlyView.The presented study focuses on the fracture behaviour of carbon‐bonded magnesia MgO–C refractories, where environmentally friendly fructose, collagen and lignin serve as temporary binding agents. The partial substitution of the source material with recycled MgO–C reduces the fracture resistance, which can be counteracted by the additional introduction ...
Marc Neumann +6 more
wiley +1 more source
Avoidance and Coalescence of Delamination Patterns [PDF]
, 2014 Delamination of coatings and thin films from substrates generates a fascinating variety of patterns, from circular blisters to wrinkles and labyrinth domains, in a way that is not completely understood.
Bertalan, Zsolt +3 more
core +2 more sources
Advanced Engineering Materials, EarlyView.Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm +5 more
wiley +1 more source
Wnt Signaling in Neural Crest Ontogenesis and Oncogenesis. [PDF]
, 2019 Neural crest (NC) cells are a temporary population of multipotent stem cells that generate a diverse array of cell types, including craniofacial bone and cartilage, smooth muscle cells, melanocytes, and peripheral neurons and glia during embryonic ...
Hao, Hongyan +4 more
core +2 more sources
Assessing Altered Coating Adhesion on Plasma‐Deoxidized Surfaces Under Oxygen‐Free Conditions
Advanced Engineering Materials, EarlyView.This study demonstrates the effectiveness of atmospheric pressure plasma pretreatment in modifying silicon and stainless steel surfaces to improve adhesion. Argon‐hydrogen plasma increases surface roughness and improves adhesion strength, whereas pure argon results in smoother surfaces and structural changes.
Selina Raumel +6 more
wiley +1 more source
, 2019 Most of the existing methods for fatigue-driven delamination are limited to two-dimensional (2D) applications or their predictive capabilities have not been validated in three-dimensional (3D) problems.
Bak, Brian L. V. +6 more
core +1 more source
Validation of low velocity impact modelling on different stacking sequences of CFRP laminates and influence of fibre failure [PDF]
, 2013 This paper presents a validation of low-velocity impact Finite Element (FE) modelling. Based on switching ply location of reference layup [02,452,902,-452]s T700GC/M21 laminated plates from Bouvet et al.
Bouvet, Christophe +2 more
core +3 more sources