Results 231 to 240 of about 1,254,509 (299)

Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials

Advanced Engineering Materials, EarlyView.
Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai, Xinrui Sarah Niu, Zhao Qin   +2 more
wiley   +1 more source

Early Intervention as a Way of Reducing Neurocognitive Delay in Pediatric Sickle Cell Patients. [PDF]

Cureus
Wilson L, Riskin SI.
europepmc   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

Toward Disease-Modifying Therapies in Type 1 Diabetes: Focus on Teplizumab. [PDF]

Diabetes Care
Mathieu C, Mathieu C, Sims EK, Chatenoud L, James EA, Atkinson MA, Herold KC.   +6 more
europepmc   +1 more source

Synthesis of a Novel Thermoresponsive S53P4 Bioactive Glass Extract–Poloxamer 407 Injectable Hydrogels: Assessment of Biocompatibility and Antimicrobial Properties

Advanced Engineering Materials, EarlyView.
This study investigates innovative thermoreversible hydrogels derived from S53P4 bioactive glass extracts to aid in the healing of infected diabetic foot wounds. These injectable gels, which gel at body temperature, release beneficial ions and remain stable over time.
Marian G. Vargas Guerrero, Adrian Stiller, Alex Nygård, Matej Krivulka, Lars Galema, Erwin Peters, Jimmy Lucchesi, Peter Uppstu, Leena Hupa, Jacobus J. C. Arts   +9 more
wiley   +1 more source

Phenotypic variability in female individuals with the NAA10 missense variants p.(L126R), p.(L126V), or p.(F128L) leading to NAA10-related syndrome. [PDF]

Mol Cell Pediatr
Bühler A, Aigner-Radakovics K, Diofano F, Marchi E, Weinmann-Emhardt K, Paquay A, Lilja SV, Rosensteiner B, Harpell R, Bernard E, Just S, Bittner RE, Lyon GJ, Kustermann M.   +13 more
europepmc   +1 more source

Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics

Advanced Engineering Materials, EarlyView.
Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost, Lionel Presmanes, Soléna Colin, Marie Vidal, Sophie Guillemet‐Fritsch   +4 more
wiley   +1 more source

Enhancing large particle recovery in high-throughput functional cell sorting through ΔBOP optimization. [PDF]

Sci Rep
Sakamoto N, Shibata E, Yoshimura M, Namura H, Yanashita Y, Masuhara S, Uehara Y, Yamane K, Kasai H, Furuki M, Hayashi Y.   +10 more
europepmc   +1 more source

Evaluating Energy Absorption Performance of Filled Lattice Structures

Advanced Engineering Materials, EarlyView.
Maximum stress must be considered to robustly evaluate energy absorber designs. This approach was applied to compare all types of absorbers in a single Ashby diagram and determine the utility of filling lattice voids with a second material. High‐performance fillers can improve the performance of lattices that are limited by buckling or catastrophic ...
Christian Bonney, William P. King, Iwona Jasiuk   +2 more
wiley   +1 more source