Results 41 to 50 of about 162,432 (304)
Thermoreflectance Detection of Point Defects Resulting from Focused Ion Beam Milling
Advanced Engineering Materials, EarlyView.Focused ion beam (FIB) milling is a common tool for nanoscale material processing, however irradiation damage, redeposition, and contamination can occur. We use several characterization tools to show FIB‐induced effects beyond 1 mm from the milled area.
Thomas W. Pfeifer +3 more
wiley +1 more source
Journal of Materials Research and Technology, 2020 This study aims to elucidate the behavior of diffusible hydrogen and delayed fracture in martensitic steel with 1500 MPa strength during automotive painting process and under vehicle service conditions.
Hye-Jin Kim +6 more
doaj +1 more source
Influence of Timing on Surgical Outcomes for Acute Humeral Shaft Fractures
Advances in Orthopedics, 2021 Surgical treatment for humeral shaft fractures has been reported to yield satisfactory results; however, there may be complications, such as delayed bone union, nonunion, iatrogenic radial nerve injury, and infection.
Ryogo Furuhata +4 more
doaj +1 more source
On the Use of Gallic Acid as a Potential Natural Antioxidant and Ultraviolet Light Stabilizer in Cast-Extruded Bio-Based High-Density Polyethylene Films [PDF]
, 2019 This study originally explores the use of gallic acid (GA) as a natural additive in bio-based high-density polyethylene (bio-HDPE) formulations. Thus, bio-HDPE was first melt-compounded with two different loadings of GA, namely 0.3 and 0.8 parts per ...
Balart, Rafael +5 more
core +2 more sources
Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials
Advanced Engineering Materials, EarlyView.Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai +2 more
wiley +1 more source
BMC Musculoskeletal Disorders, 2023 Background/purpose Impaired healing is a feared complication with devastating outcomes for each patient. Most studies focus on geriatric fracture fixation and assess well known risk factors such as infections.
Sascha Halvachizadeh +6 more
doaj +1 more source
Management of subtrochanteric femur fractures with internal fixation and recombinant human bone morphogenetic protein-7 in a patient with osteopetrosis: a case report [PDF]
, 2010 Introduction Osteopetrosis is a group of conditions characterized by defects in the osteoclastic function of the bone resulting in defective bone resorption.
Robert D Golden +15 more
core +2 more sources
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Early Stage Cavitation Erosion within Ceramics: An Experimental Investigation [PDF]
, 2009 Six ceramic material types were considered within an experimental investigation to identify the erosion damages mechanisms resulting from cavitation exposure.
Fatjo, Gonzalo +3 more
core +1 more source
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source