Results 141 to 150 of about 135,780 (323)

Sintering Effects on the Densification of Nanocrystalline Hydroxyapatite

, 2011
S. Ramesh, C.Y. Tan, M. Amiriyan, W.D. Teng   +3 more
openalex   +1 more source

Incremental Strategies for suburban densification [PDF]

, 2020
Guy Marriage, Tegan Wardle
openalex   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Microstructural Evolution and Vacancy Defect Formation in Mn–Mo–Ni RPV Steel Under Low Cycle Fatigue: Insights From EBSD and PALS

Advanced Engineering Materials, EarlyView.
Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar, Dhanadeep Dutta, G. Bharat Reddy   +2 more
wiley   +1 more source

Structure, densification and electrical properties of Gd3+ and Cu2+ co-doped ceria solid electrolytes for SOFC applications: Effects of Gd2O3 content

, 2017
Thamyscira H. Santos, João P.F. Grilo, Francisco J.A. Loureiro, Duncan P. Fagg, Fábio C. Fonseca, Daniel A. Macedo   +5 more
openalex   +2 more sources

Tribological Performance of 60NiTi Alloy Under Varying Contact Conditions and Elevated Temperatures in Linear Reciprocating Sliding

Advanced Engineering Materials, EarlyView.
This study investigates the tribological response of 60NiTi alloy under dry, water‐lubricated and high‐temperature conditions. The alloy exhibits decreasing wear volume and friction with increasing temperature due to the formation of protective oxide layers. The work clarifies dominant wear mechanisms and demonstrates the suitability of 60NiTi for high‐
Anthony Onyebuchi Okoani, Miguel Angel Selles, Maziar Ramezani   +2 more
wiley   +1 more source

Effect of internal curing by superabsorbent polymers on the densification and microstructural development of cementitious materials exposed to different environmental conditions

, 2023
Geuntae Hong, Jiyoung Kim, Chiwon Song, Jung Heum Yeon, Seongcheol Choi   +4 more
openalex   +1 more source

Mapping horizontal and vertical urban densification in Denmark with Landsat time-series from 1985 to 2018: A semantic segmentation solution [PDF]

, 2020
Tzu‐Hsin Karen Chen, Chunping Qiu, Michael Schmitt, Xiao Xiang Zhu, Clive E. Sabel, Alexander V. Prishchepov   +5 more
openalex   +1 more source

Vibrational disorder and densification-induced homogenization of local elasticity in silicate glasses [PDF]

, 2021
Omar Benzine, Zhiwen Pan, Courtney Calahoo, Michał Boćkowski, Morten M. Smedskjær, Walter Schirmacher, Lothar Wondraczek   +6 more
openalex   +1 more source

Characterization of Nitinol Produced by Laser Powder Bed Fusion for Mechanical Metamaterial Applications

Advanced Engineering Materials, EarlyView.
Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek, Jakub Hurník, Miroslav Šmíd, Ondřej Zobač, Melanie Todt, Daniel Koutný   +5 more
wiley   +1 more source