Results 181 to 190 of about 135,780 (323)

Mechanostat-Informed Strain Mapping of Osseodensification-Inspired Peri-Implant Densification Versus Conventional Drilling in Osteoporotic-like Low-Density Cancellous Bone: A 3D Static Linear Finite Element Analysis. [PDF]

J Funct Biomater
Tuzlali M, Baki N, Önügören Nİ, Aral K, Bahçe E, Aral CA.   +5 more
europepmc   +1 more source

Thermomechanical Fatigue and Creep–Fatigue Interaction of Inconel 718 Additively Manufactured by Laser Beam Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth, Tomáš Babinský, Jan Lars Riedel, Wen Hao Kan, Aijun Huang, Martin Heilmaier, Ivo Šulák   +6 more
wiley   +1 more source

Concurrent optimization of fracture toughness, thermal conductivity, and tribological behavior in C_f/Si₃N₄ composites via phase driven selection. [PDF]

Sci Rep
Hoseinzadeh S, Estarki MRL, Ghasemi A, Zahabi S, Gordani G, Sharifi EM.   +5 more
europepmc   +1 more source

Phenomenological and Physically Based Modeling of Flow Stress and Strengthening Mechanism of Inconel 718

Advanced Engineering Materials, EarlyView.
Nickel‐based alloys are widely used in high‐temperature applications due to their excellent mechanical strength and oxidation resistance. However, properties such as high‐temperature strength and pronounced work‐hardening make them difficult to machine.
Soheil Rooein, Oliver Schenk, Christoph Broeckmann   +2 more
wiley   +1 more source

Structural Investigation of Wood-Inspired Cell Wall Geometries Using Additive Manufacturing: Compression Testing and Finite Element Analysis Validation

BioResources
Mechanical properties of wood-inspired cell wall geometries were considered through compression testing and Finite Element Analysis (FEA) with ANSYS simulation.
Murat Aydin, Yasin Furkan Gorgulu
doaj  

The effect of Y2O3 on the grain growth and densification of W matrix during low temperature sintering: Experiments and modelling

, 2019
Zhi Dong, Nan Liu, Weiqiang Hu, Xiangwei Kong, Zongqing Ma, Yongchang Liu   +5 more
openalex   +1 more source

Air‐Pressure–Actuated Vibroacoustic Metamaterial With Tunable Bandgap: Design, Modeling, and Characterization

Advanced Engineering Materials, EarlyView.
This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal, Michael M. Becker, Sarah C. L. Fischer   +2 more
wiley   +1 more source

Breaking through safety performance stagnation in autonomous vehicles with dense learning. [PDF]

Nat Commun
Feng S, Zhu H, Sun H, Yan X, He L, Yang J, Su G, Li B, Li S, Wang L, Shen S, Liu HX.   +11 more
europepmc   +1 more source

On the Influence of Antioxidants and Recycled MgO–C Source Material on the Mechanical Properties of Carbon‐Bonded Magnesia Refractories

Advanced Engineering Materials, EarlyView.
The presented study focuses on the fracture behaviour of carbon‐bonded magnesia MgO–C refractories, where environmentally friendly fructose, collagen and lignin serve as temporary binding agents. The partial substitution of the source material with recycled MgO–C reduces the fracture resistance, which can be counteracted by the additional introduction ...
Marc Neumann, Tom Weber, Jana Hubálková, Florian Kerber, Dinesh Kumar Gunasekar, Hans Jelitto, Christos G. Aneziris   +6 more
wiley   +1 more source

Load dependence of densification in glass during Vickers indentation test

, 2011
Yoshinari Kato, Hiroki Yamazaki, Satoru ITAKURA, Satoshi Yoshida, Jun Matsuoka   +4 more
openalex   +2 more sources