Results 201 to 210 of about 15,178 (333)

The effects of anodization and instrumentation on titanium abutment surface characteristics and biofilm formation

Journal of Prosthodontics, EarlyView.
Abstract Purpose To assess the impact of anodization and instrumentation on titanium abutment surface characteristics (surface roughness and wettability) and biofilm formation (viability and mass). Materials and Methods Titanium discs were obtained from pre‐milled abutment blanks made of titanium‐6aluminum‐7niobium alloy.
Weiqing Liu, Richard L. Gregory, Chao‐Chieh Yang, Yusuke Hamada, Wei‐Shao Lin   +4 more
wiley   +1 more source

Comparative evaluation of the efficiency of different decontamination protocols for reusing healing abutments: An in vitro study. [PDF]

J Oral Biol Craniofac Res
Patel D, Anasane NS, Madhav VNV.
europepmc   +1 more source

Finite element analysis of primary healing implants with different transmucosal designs

Journal of Prosthodontics, EarlyView.
Abstract Purpose This study aimed to assess the response of peri‐implant tissues, both hard and soft, to mechanical stress when using a primary healing implant (PHI) with two different transmucosal profiles: concave (Model A) and divergent (Model B). The investigation also sought to observe bone modeling under post‐extraction conditions.
Mario Ceddia, Tea Romasco, Luca Comuzzi, Alessandro Cipollina, Adriano Piattelli, Natalia Di Pietro, Bartolomeo Trentadue   +6 more
wiley   +1 more source

The fracture strength by a torsion test at the implant-abutment interface [PDF]

, 2015

core   +1 more source

Marginal gap of printed, milled, and heat‐pressed two‐piece polyetheretherketone abutments before and after thermal cycling, and their pull‐off bond strength after thermal cycling

Journal of Prosthodontics, EarlyView.
Abstract Purpose To evaluate the marginal gap of two‐piece polyetheretherketone (PEEK) abutments fabricated with different methods, before and after thermal cycling, while also focusing on their pull‐off bond strength. Materials and Methods A two‐piece abutment was virtually designed after digitizing a titanium‐base (Ti‐base) abutment.
Almira Ada Diken Türksayar, Burcu Kanpalta, Naime Bilinç Bulucu, Sandra Schulnig, Sebastian Spintzyk, Münir Demirel, Mustafa Borga Donmez   +6 more
wiley   +1 more source

The selection criteria of temporary or permanent luting agents in implant-supported prostheses: In vitro study [PDF]

, 2016
Brizuela Velasco, Aritza, Ellacuria Echevarría, Joseba, González González, Ignacio Ramón, Llanos Lanchares, Héctor de, Álvarez Arenal, Ángel   +4 more
core   +1 more source

Biomechanics of the implant‐supported full arch fixed complete denture manufactured by milling and injection techniques: An experimental and FEA study

Journal of Prosthodontics, EarlyView.
Abstract Purpose This study aims to characterize the mechanical properties of implant‐supported full arch fixed complete dentures manufactured by milling and injection techniques. Materials and Methods Twenty‐two samples with milling and injection manufacturing techniques were fabricated.
Mustafa Gürkan, Ovul Kumbuloglu, Makbule Heval Şahan, Mert Narin, Halis Kandaş, Yusuf Arman, Hasan Yildiz, Mahmut Pekedis   +7 more
wiley   +1 more source

Enhancing digital workflows for removable partial dentures: A novel diagnostic surveyor and designer

Journal of Prosthodontics, EarlyView.
Abstract Removable partial dentures (RPDs) are a valuable treatment option in prosthodontics, often selected due to patient‐specific limitations such as financial constraints, inadequate bone support, or medical contraindications to other prosthetic solutions.
Ahmed Mahrous, David L. Botsko, Tamer El‐Gendy, Amira Elgreatly   +3 more
wiley   +1 more source

Jaw in a Day: How to Perform Your First Case-Our Workflow. [PDF]

Craniomaxillofac Trauma Reconstr
Mosquera C, Marwan H.
europepmc   +1 more source

Evaluation of the accuracy of digital workflow for implant‐supported full‐arch fixed dental prostheses using a novel micro‐CT measurement technique

Journal of Prosthodontics, EarlyView.
Abstract Purpose This study aims to evaluate the accuracy of fit of full‐arch implant titanium frameworks fabricated from a fully digital workflow using a novel micro‐CT measurement technique. Materials and Methods A 3D‐printed model with four implant analogs was fabricated.
Amira Fouda, Chris Wyatt, Anthony McCullagh, Siddharth R. Vora, Nancy L. Ford, Mohamed Gebril   +5 more
wiley   +1 more source