Results 61 to 70 of about 21,155 (203)
Development Of Low Cost Block Mold For Copper Alloy Casting [PDF]
, 2016 Suitable block mold formulations for copper alloy casting have been developed and the formulations used were 25% plaster of paris (POP), 75% silica sand and 31-37% water. Silica sand with a grain size of 106-212 µm was added into dilute suspension of POP
Ahmad Salihin, Samsudin +4 more
core
Influence of low concentration acid treatment on lithium disilicate core/veneer ceramic bond strength [PDF]
, 2013 Objective: This study evaluated the influence of low concentration acid treatment on the shear bond strength between lithium disilicate (LD) infrastructure and veneering porcelain.
Conti, Paulo César Rodrigues +4 more
core +1 more source
Clinical application of additive manufacturing in maxillofacial prosthetics: A scoping review
Journal of Prosthodontics, EarlyView.Abstract Purpose Digital workflows provide significant advances in prosthodontics, especially in terms of accuracy, reduced treatment duration, and quality of life. Moreover, additive manufacturing (AM) is particularly adapted for the fabrication of personalized complex prototypes required for the prosthetic rehabilitation of maxillofacial defects ...
Hélène Magro +2 more
wiley +1 more source
Comparative Tensile Strengths of Preceramic and Postceramic Solder Connectors Using High-Palladium Alloy [PDF]
, 2004 Purpose: To evaluate the tensile strength properties of Rx Naturelle Plus and Option (high-palladium) alloys on soldered connectors under simulated preceramic and postceramic soldering conditions.
Shehab, Abdul-Hadi
core +2 more sources
Journal of Prosthodontics, EarlyView.Abstract Purpose To evaluate the impact of surface treatments and chemical denture cleansers on the surface color stability, gloss, and wettability of compression‐molded, 3D‐printed, and milled denture base materials. Materials and Methods Specimens (12 × 16 × 7 mm) were fabricated from a standardized STL file in three denture base materials ...
Suonds Alareifi +5 more
wiley +1 more source
Laboratory Fabrication Procedures of a Metal Partial Denture Framework [PDF]
, 2003 Jednokomadni lijevani metalni odljev sastavni je dio svake metalne djelomične proteze. Njegova izradba zahtijeva preciznost i tehničara i stomatologa - od početne faze kada se još planira taj mobilni nadomjestak, pa tijekom otiskivanja, izlijevanja ...
Dubravka Knezović-Zlatarić +2 more
core +1 more source
Bone response to biosilicates® with different crystal phases [PDF]
, 2010 The aim of this study was to investigate the histological and histomorphometrical bone response to three Biosilicates with different crystal phases comparing them to Bioglass®45S5 implants used as control.
AZENHA, Marcelo Rodrigues +2 more
core +1 more source
The Anatomical Record, Volume 309, Issue 4, Page 864-911, April 2026.Abstract The trigeminus nerve (cranial nerve V) is a large and significant conduit of sensory information from the face to the brain, with its three branches extending over the head to innervate a wide variety of integumentary sensory receptors, primarily tactile.
Juri A. Miyamae +4 more
wiley +1 more source
Understanding the Workflows in Non‐Guided and Static Computer‐Assisted Implant Surgery
Clinical and Experimental Dental Research, Volume 12, Issue 2, April 2026.ABSTRACT Contemporary implant dentistry aims to achieve long‐term biological, esthetic, and functional successful outcomes. Thus, instrumental to this aim is designing an integrated system in which the supported prosthesis & components, anatomical and phenotypical tissue characteristics, and the fixture act synergistically to maintain peri‐implant ...
Adria Jorba‐Garcia +6 more
wiley +1 more source
Tekes projekti SuperMachines loppuraportti [PDF]
, 2015 Tutkimuksessa kerättiin best practice aineistoa ja kehitettiin internet alusta kerätyn aineiston tutkimiseen ja hakujen suorittamiseen. Aineisto löytyy internet osoitteesta: http://www.amcase.info/. Rekisteröitymällä kuka vain voi syöttää alustalle lisää
Björkstrand, Roy +6 more
core