Results 21 to 30 of about 13,231 (263)

Evaluation of the effect of tooth polishing on color stability after in-office bleaching treatment

Revista de Odontologia da UNESP, 2020
Introduction One of the most commonly used corrective methods for staining teeth is tooth bleaching. However, subclinical alterations may occur in the micromorphology of dental tissues during the bleaching procedure, such as increases in porosity and ...
Luís Felipe ESPÍNDOLA-CASTRO, Pamella Robertha Rosselinne Paixão CELERINO, Tácyla Alves do NASCIMENTO, Gabriela Queiroz de Melo MONTEIRO, Tereza Cristina CORREIA   +4 more
doaj   +1 more source

Evaluation of Bulk Fill Composite Roughness Polished with Spiral Rubber Discs: An In-vitro Study [PDF]

Journal of Clinical and Diagnostic Research, 2022
Introduction: Restorations with high surface roughness directly influences restorative procedure longevity. When used correctly, polishing systems optimises the quality, aesthetics and longevity of composite resins.
Glaucia Danielle Ferreira Da Silva, Marlon Ferreira Dias, Cláudio Eufrásio Medeiros Lins, Eric Roberto Soares Xavier De Siqueira, Amina Kadja Martins Cahu, Natália Gomes De Oliveira, Renata Albuquerque Cavalcanti Almeida, Luís Felipe Espíndola-Castro   +7 more
doaj   +1 more source

Effects of different polishing techniques on the surface roughness of dental porcelains

Journal of Applied Oral Science, 2010
OBJECTIVE: The purpose of this study was to evaluate the effects of different polishing techniques on the surface roughness of dental porcelains. MATERIAL AND METHODS: Fifty-five cylindirical specimens (15x2 mm) were prepared for each feldspathic (Vita ...
Işil Sarikaya, Ahmet Umut Güler   +1 more
doaj   +1 more source

Comparison of the polishing effects of polyetheretherketone materials under different chairside polishing systems

口腔疾病防治, 2023
Objective The polishing effects of different compositions of chairside polishing systems on polyetheretherketone (PEEK) were compared to provide a reference for the rational selection of polishing systems for this material in clinical settings. Methods A
LIU Hengyan, LIU Yuchen, LI Kangjie, TIAN Min, NIU Lina, BAI Shizhu , FANG Ming   +6 more
doaj   +1 more source

Effect of glazing and polishing on opalescence and fluorescence of dental ceramics

Clinical and Experimental Dental Research, 2022
AbstractObjectiveTooth enamel has opalescence and fluorescence, which should be mimicked by esthetic dental restorations. The purpose of this study was to compare the effects of glazing and polishing on the opalescence and fluorescence of dental ceramics.Materials and MethodsTwenty‐four discs were fabricated of feldspathic, IPS e.max, zirconia, and ...
Hashemikamangar, Sedighe Sadat, Nahavandi, Alireza Mahmoudi, Daryadar, Marzieh, Valizadeh, Sara, Özcan, Mutlu   +4 more
openaire   +4 more sources

Polishing Systems on Surface Roughness and the Color Stability of Leucite-Reinforced Feldspathic Ceramic

Essentials of Dentistry, 2021
Objective: The purpose of this in vitro study was to determine the effect of different polishing methods applied on the surface roughness and color stability of leucite-reinforced feldspathic ceramic. Methods: The leucite-reinforced feldspathic ceramic
Gamze PAKEN
doaj   +1 more source

MAIN PROPERTIES OF ABRASIVE DENTISTRY MATERIALS UTILIZED IN POLISHING OF REMOVABLE DENTURE BASES

Український стоматологічний альманах, 2018
The requirements to the quality of dental prostheses are currently very high. All dental prostheses need thorough final finishing through filing and polishing in order to obtain smooth, polished, shiny and esthetic surface.
V.F. Makeev, Yu.R. Hunovskyi, R.P. Hunovska   +2 more
doaj   +1 more source

The effect of polishing protocol on surface gloss of different restorative resin composites

Biomaterial Investigations in Dentistry, 2020
Aim The purpose of this in vitro study was to determine the effects of different polishing protocols on the surface gloss (SG) of different commercial dental resin composites (RCs). Material and methods A total of 147 block-shaped specimens (40 mm length
Lippo Lassila, Eija Säilynoja, Roosa Prinssi, Pekka K. Vallittu, Sufyan Garoushi   +4 more
doaj   +1 more source

Evaluation of Different Polishing Systems and Speeds for Dental Zirconia [PDF]

Journal of Prosthodontics, 2015
AbstractPurposeTo evaluate two polishing systems and three polishing speeds on the gloss, roughness, and heat production of yttria stabilized tetragonal zirconia polycrystal (Y‐TZP).Materials and MethodsA Y‐TZP block (Zenostar Zr Translucent) was sectioned into 4‐mm‐thick sections.
Ramakiran, Chavali, Chee Paul, Lin, Nathaniel C, Lawson   +2 more
openaire   +2 more sources

An in vitro study to compare glazed and polished surfaces of feldspathic porcelain and comparing three different polishing systems

Indian Journal of Dental Sciences, 2017
Aim and Objectives: Effective finishing and polishing of dental restorations provides for oral health, function and aesthetics. There are studies which state that porcelain should be glazed after chairside adjustments, whereas, some studies advocate that
Aakriti Singh, Bhaskar Sengupta, Harinder Kuckreja, K B. S Kuckreja   +3 more
doaj   +1 more source