Evaluation of shear bond strength based on substructure materials and ceramic veneering techniques
Journal of Prosthodontics, EarlyView.Abstract Purpose Bilayered restorations have both the strength of the substructure material and the esthetics of the veneer material; however, they should have appropriate bonding between the two materials. This study aimed to evaluate the shear bond strength (SBS) according to the substructure material and veneering technique used in bilayered ...
Han‐Sol Song +4 more
wiley +1 more source
Strength Properties of Preceramic Brazed Joints of a Gold-Palladium Alloy with a Microwave-assisted Oven and Gas/Oxygen Torch Technique [PDF]
, 2014 Statement of problem The effect of microwave brazing on the strength properties of dental casting alloys is not yet known. Purpose The purpose of this study was to compare the strength properties of preceramic brazed joints obtained by using a microwave
Dunford, Robert +3 more
core +1 more source
Zirconia in fixed prosthesis. A literature review [PDF]
, 2014 Statement of problem: Evidence is limited on the efficacy of zirconia-based fixed dental prostheses. Objective: To carry out a literature review of the behavior of zirconium oxide dental restorations.
Agustín Panadero, Rubén +4 more
core +1 more source
Advances in dental veneers: materials, applications, and techniques
Clinical, Cosmetic and Investigational Dentistry, 2012 Núbia Pavesi Pini1, Flávio Henrique Baggio Aguiar1, Débora Alves Nunes Leite Lima1, José Roberto Lovadino1, Raquel Sano Suga Terada2, Renata Corrêa Pascotto21Area of Restorative Dentistry, Piracicaba ...
Pini NP +5 more
doaj
Journal of Prosthodontics, EarlyView.Abstract Purpose To investigate the effects of the elemental composition and the manufacturing process of cobalt chromium–molybdenum (CoCr–Mo), cobalt chromium–tungsten (CoCr–W), and CoCr–Mo‐W alloys on metal–ceramic bond strength. Materials and Methods Six CoCr‐based alloys were included in this study, a were classified into three different groups ...
Youssef S. Al Jabbari +3 more
wiley +1 more source
Porcelain Surface Roughness, Color and Gloss Changes after Orthodontic Bonding [PDF]
, 2006 The purpose of this study was to evaluate the alteration in surface characteristics after orthodontic debonding of two types of porcelain systems commonly used in prosthetic dentistry. For this purpose, porcelain specimens were fabricated from low-fusing
Bradley, T. Gerard +3 more
core +1 more source
A comparison of the tribological behaviour of Y-TZP in tea and coffee under micro-abrasion conditions [PDF]
, 2013 The micro-abrasion of Y-TZP, a candidate dental restorative material, was investigated in a range of caffeine-containing solutions which included tea and coffee.
Sharifi, Shayan, Stack, Margaret
core +1 more source
A technique for the management of screw access opening in cement-retained implant restorations
Dental Hypotheses, 2014 Introduction: Abutment screw loosening has been considered as a common complication of implant-supported dental prostheses. This problem is more important in cement-retained implant restorations due to their invisible position of the screw access opening.
Hamid Kermanshah, Tahereh Bitaraf
doaj +1 more source
Design of quantum correlation based automatic focus detection system during dental laser operation [PDF]
arXiv, 2019 Dental laser has been developed recently and gradually replaced the conventional dental treatment methods, especially in dental caries removal. The utility of laser in dentistry contributes to reduce the pain during surgery and decrease the risk of sequelae after surgery.
arxiv
Addition of platinum and silver nanoparticles to toughen dental porcelain.
Dental materials journal, 2012 Several studies have investigated toughening porcelain that is layered over a frame or a core. The introduction of residual compressive stress to the surface of porcelain has been shown to be effective to strengthen it.
T. Fujieda +5 more
semanticscholar +1 more source