Translucency of a Dental Porcelain Mixed by Two Ceramic Slurry Methods: A Bayesian Comparison [PDF]
International Journal of Dentistry, 2022 Background. The ceramics industry produces porcelain pastes using a controlled ratio of water and porcelain powder. Two methods are used to produce a dental porcelain paste: one-step mixing or incremental mixing. Objective.
Catalina Serna-Meneses +7 more
doaj +3 more sources
A study on the discoloration of different dental porcelain systems [PDF]
European Oral Research, 2023 Purpose:This study aimed to investigate the discoloration of four types of dental porcelain systems (feldspathic, monolithic zirconia, lithium disilicate, and leucite glassceramic) with various surface treatments (glazed and mechanically polished) after ...
Mehmet Çağatay Ulucan +2 more
doaj +2 more sources
Evaluation of Hardness and Fracture Toughness of Feldspathic Porcelain by Various Surface Finishing Techniques [PDF]
Journal of Clinical and Diagnostic Research, 2022 Introduction: Dental porcelain is fired at a high temperature inside the furnace and subsequently glazed for intraoral use as a restoration. There is no clarity on the correlation between physical properties of porcelain and its surface finishing ...
Khalid Ghiaz +6 more
doaj +1 more source
A Scanning Electron Microscopy and Energy Diffraction X-Ray Spectroscopy Study to Evaluate the Effect of Firing Temperature at the Ceramic-Noble Metal Alloy Interface in Porcelain Fused to Metal Restorations [PDF]
Journal of Clinical and Diagnostic Research, 2021 Introduction: Porcelain Fused to Metal (PFM) restorations offer aesthetics of ceramics and the strength of metal hence are the gold standards of fixed partial dentures.
Arvind Tripathi +4 more
doaj +1 more source
Translucency of Dental Porcelains [PDF]
Journal of Dental Research, 1980 The translucency of comparable shades of five dental porcelains was determined. Both direct transmittance and total transmittance were measured at wavelengths of 400 - 700 nm. For 1 mm of porcelain, the values for direct transmittance were low and averaged 0.13 percent, whereas the values for total transmittance averaged 26.8 percent.
Brodbelt, R. H. W. +2 more
openaire +3 more sources
Sintering of Dental Porcelain Enamels [PDF]
Journal of Dental Research, 1976 This study showed the effects of sintering temperature and atmospheric pressure on the density, tensile strength, and microstructure of porcelain enamels. Although the densities of the opaque porcelains were higher, they were weaker than the gingival porcelains.
Meyer, J. M., O'Brien, W. J., Yu, C. U.
openaire +3 more sources
KEMAMPUAN LEKAT RESIN KOMPOSIT PADA REPARASI RESTORASI PORSELEN YANG FRAKTUR
Journal of Dentistry Indonesia, 2015 Since ceramic and metal ceramic restorations in crown and bridge have the potential to fracture, repairing porcelain restorations has become a serious cosmetic and clinical problem.
Ali Noerdin
doaj +1 more source
Porcelain Laminate Veneer Applications in Upper Anterior Region: Case report
Bezmiâlem Science, 2020 Recently, effects of rapidly developing technology have been seen in the dentistry. Advances in materials enable minimally invasive treatments in which dental tissue is preserved in order to provide esthetics.. Porcelain laminate veneer technique, one of
Zeynep Buket KAYNAR, Nazmiye DÖNMEZ
doaj +1 more source
Knowledge protocol of direct and indirect Veneers among dental practitioners - A case study
Polytechnic Journal, 2023 Dental veneers are constructed from different materials such as porcelain, pressed ceramic, processed composite, or directly applied composite.The purpose of this study was to ascertain the preferred dental materials for veneers and the knowledge about ...
Sazan M. Azeez +3 more
doaj +1 more source
PATTERN OF DEMAND FOR MAKING DENTURES AT DENTAL LABORATORY IN SURABAYA CITY, INDONESIA
Journal of Vocational Health Studies, 2019 Background: Dental laboratory in Surabaya frequently make various kinds of the denture. But surely there is a case that was the most commonly accepted, to adjust to the needs of dental laboratories on the priorities of the work was done, it was necessary
Okti Setyowati +2 more
doaj +1 more source