Results 31 to 40 of about 611 (154)

Fracture Strength and Bending of Fiber-Reinforced Composites and Metal Frameworks in Fixed Partial Dentures

Frontiers in Dentistry, 2008
Objective: This in vitro study evaluated the fracture strength and bending amount of twotypes of fiber reinforced composite (FRC) and cast metal frameworks used for fabrication of inlay fixed partial dentures (IFPDs). Materials and Methods: Seventy-two
M. Sadeghi
doaj  

Systematic Review Evaluating the Influence of Veneering Design on the Clinical Outcome of All‐Ceramic Implant‐Supported 3–4 Units and Full Arch Fixed Dental Prostheses

Journal of Esthetic and Restorative Dentistry, Volume 38, Issue 9, Page 1691-1707, September 2026.
ABSTRACT Objective To systematically assess survival, failure, and complication rates of all‐ceramic implant‐supported monolithic and micro‐veneered FDPs (i‐FDPs) in partially/completely edentulous patients compared to veneered restorations. Materials and Methods An electronic search identified prospective clinical studies on all‐ceramic i‐FDPs with at
Shaza Bishti, Stefan Wolfart, Marcel Zwahlen, Lukas Waltenberger   +3 more
wiley   +1 more source

Finite Element Analysis of IPS Empress II Ceramic Bridge Reinforced by Zirconia Bar.

Frontiers in Dentistry, 2012
The aim of this study was to determine the effect of trenched zirconia bar on the von Mises stress distribution of IPS -Empress II core ceramics.The three-dimensional model including a three-unit bridge from the second premolar to the second molar was ...
H Kermanshah, T Bitaraf, A Geramy
doaj  

Influence of Different Multilayer Zirconia Materials on the In Vitro Load‐Bearing Capacity of Resin‐Bonded Fixed Partial Dentures in the Posterior Region

Journal of Esthetic and Restorative Dentistry, Volume 38, Issue 9, Page 1854-1863, September 2026.
ABSTRACT Objective Comparison of the load‐bearing capacity and failure pattern of posterior resin‐bonded fixed partial dentures (RBFPDs) differing in retainer design, zirconia material, and vertical nesting position. Materials and Methods RBFPDs replacing a maxillary first molar were fabricated with 2 retainer designs (inlay‐retained, IR; wing‐retained,
Moritz Waldecker, Maria Sophie Heller, Stefan Rues, Peter Rammelsberg, Wolfgang Bömicke   +4 more
wiley   +1 more source

Model‐Based Cost‐Effectiveness of Direct Restorations: Amalgam Dominates

Community Dentistry and Oral Epidemiology, Volume 54, Issue 4, Page 407-417, August 2026.
ABSTRACT Objectives A phase‐down of dental amalgam use has been mandated and the feasibility of its phase‐out in England by 2030 is being explored. Amalgam use in English National Health Service (NHS) care still predominates for posterior restorations, though access to this care is increasingly limited.
O. Bailey, S. J. Stone, G. Taylor, L. Ternent, C. R. Vernazza   +4 more
wiley   +1 more source

Oral Fine Motor Control in Patients With Anterior Maxillary Single Implants, Freestanding Teeth and Teeth Connected in 3‐Unit Bridges: An Experimental In Vivo Study

Clinical Oral Implants Research, Volume 37, Issue 8, Page 922-930, August 2026.
ABSTRACT Objectives The oral fine motor control is compromised in patients with full‐arch, bimaxillary bridges compared to those with natural teeth. No previous studies have examined the differences between the prosthetic treatments small anterior bridges and single anterior implants (SI). The aim of the study was to evaluate oral fine motor control in
Nicole Winitsky, Aron Naimi‐Akbar, Jan‐Ivan Smedberg, Anastasios Grigoriadis   +3 more
wiley   +1 more source

Early Clinical Experiences for Dental Students Using Near Peer Assisted Learning (NPAL)

European Journal of Dental Education, Volume 30, Issue 3, Page 1291-1306, August 2026.
ABSTRACT Introduction This paper describes Doctor of Dental Surgery students' perspectives on participating in NPAL sessions at the School of Dentistry at the University of Alberta. NPAL provides early clinical experiences (ECE) for junior students (mentees) assisted by senior students (mentors).
Anthea Senior, Colleen Starchuk, Alexandre W. Araujo, Steven Patterson, Nazlee Sharmin   +4 more
wiley   +1 more source

Load‐To‐Failure of Cantilevered Provisional Implant‐Supported Prostheses: Conventional Versus 3D‐Printed Resins

Journal of Esthetic and Restorative Dentistry, Volume 38, Issue 8, Page 1527-1533, August 2026.
ABSTRACT Objective Cantilever extensions in full‐arch implant‐supported provisional prostheses represent a clinical challenge frequently associated with biomechanical complications. This study aimed to evaluate the load‐to‐failure and deflection of acrylic and 3D‐printed resins used in the cantilever region of implant‐supported provisional prostheses ...
Térsia Cristina Silva Macedo, Carolina Neves Tannous Dib, Maribi Isomar Terán Lozada, João Pedro Alves Silva, Karla Zancopé   +4 more
wiley   +1 more source

The effect of finishing resin-bonded fixed partial dentures on postcementation tensile strength

The Journal of Prosthetic Dentistry, 1988
The Journal of Prosthetic Dentistry 59 (1988) 149-153.
Medical College of Georgia, School of Dentistry, Augusta, Ga., USA ( host institution ), Caughman, W. Frank, Comer, Robert W., Clark, Lawrence L., Lentz, David L., Zardiackas, Lyle D.   +5 more
openaire   +3 more sources

Effect of adhesives and mechanical surface treatments on the hard relining of CAD‐CAM denture bases

Journal of Prosthodontics, Volume 35, Issue 7, Page 1096-1104, August 2026.
Abstract Purpose The aim of this study was to evaluate the impact of mechanical roughening, adhesive applications, and aging on the bonding between CAD‐CAM denture base materials with distinct chemical contents and hard relining material. Materials and Methods A total of 300 denture base specimens were produced by additive, subtractive, and ...
Isil Karaokutan, Ilayda Ayvaz, Gulsum Sayin Ozel   +2 more
wiley   +1 more source