Results 151 to 160 of about 12,572 (309)

Workflow to facilitate complete denture scanning with an intraoral scanner: A technique report

Journal of Prosthodontics, EarlyView.
Abstract Scanning a denture with an intraoral scanner is typically more challenging than scanning a dentate arch. This article describes a novel technique for digitally duplicating a complete denture. The workflow involves scanning an existing denture using an intraoral scanner with the addition of specific markers and subsequently constructing a ...
Jiayi Yu, Jiayi Lu, Berna Saglik, Junying Li   +3 more
wiley   +1 more source

Management of malaligned teeth in young patients with overlay removable partial denture: series of two case reports. [PDF]

J Surg Case Rep
Elsawy A, Khan AS.
europepmc   +1 more source

Shade variability and stability in interim and definitive tooth‐colored resin‐based restorative materials: Comparing manufacturer‐claimed shades to a universal shade guide

Journal of Prosthodontics, EarlyView.
Abstract Purpose To evaluate the shade variability and stability of interim and definitive tooth‐colored restorative materials by comparing manufacturer‐claimed shades to a universal shade guide before and after thermocycling. Materials and Methods Eight commercially available tooth‐colored restorative materials were tested, including conventional ...
Amal Alfaraj, Toshiki Nagai, Wei‐Shao Lin   +2 more
wiley   +1 more source

Influence of prosthesis type and intraoral scanner‐based extraoral scanning protocol on the passive fit of CAD‐CAM verification devices

Journal of Prosthodontics, EarlyView.
Abstract Purpose To evaluate the impact of different complete‐arch digital scanning techniques and prosthesis types on the passive fit of computer‐aided design and computer‐aided manufacturing (CAD‐CAM) verification devices. Materials and Methods Two different maxillary master casts with four multi‐unit abutment (MUA) implant analogs (FP‐1 and FP‐3 ...
Toshiki Nagai, Yusuke Kuroda, Natalie Asavanant, Chao‐Chieh Yang, Dean Morton, Wei‐Shao Lin   +5 more
wiley   +1 more source

Fabrication of a Monolithic Computer-Aided Design (CAD)/Computer-Aided Manufacturing (CAM) Zirconia Crown Adapted to the Clasp of an Existing Removable Partial Denture. [PDF]

Cureus
Takebe J.
europepmc   +1 more source

Impact of monomer contamination of isopropanol during post‐rinsing on the accuracy of dental models fabricated by vat photopolymerization

Journal of Prosthodontics, EarlyView.
Abstract Purpose The aim of this study was to investigate the impact of an increasing level of monomer contamination of isopropanol (isopropyl alcohol [IPA]) during post‐rinsing on the dimensional stability of test samples produced by vat photopolymerization.
Florian Flierl, Benedikt C. Spies, Severin Rothlauf, Kirstin Vach, Ralf J. Kohal, Jörg Lüchtenborg   +5 more
wiley   +1 more source

Advances in 3D Printing for Removable Prosthetics-Insights and Perspectives. [PDF]

J Esthet Restor Dent
Schubert O, Edelhoff D, Güth JF, Schweiger J.   +3 more
europepmc   +1 more source

Assessing readability and accuracy of content produced by the American College of Prosthodontists and large language models for patient education in prosthodontics

Journal of Prosthodontics, EarlyView.
Abstract Purpose This study aims to evaluate the readability and accuracy of content produced by ChatGPT, Copilot, Gemini, and the American College of Prosthodontists (ACP) for patient education in prosthodontics. Materials and Methods A series of 26 questions were selected from the ACP's list of questions (GoToAPro.org FAQs) and their published ...
Soni Prasad, Merve Koseoglu, Stavroula Antonopoulou, Heidi Marie Huber, Atousa Azarbal, Sri Kurniawan, Cortino Sukotjo   +6 more
wiley   +1 more source

Mechanical Effects of Implant Position on an Implant-Supported Removable Partial Denture Using Three-Dimensional Finite-Element Analysis. [PDF]

Cureus
Nakamura K, Kumano H, Ozawa S, Takebe J.
europepmc   +1 more source

Effect of material, prosthesis height, and aging on the fracture strength of additively and subtractively manufactured implant‐supported cantilevered prostheses

Journal of Prosthodontics, EarlyView.
Abstract Purpose This study aimed to evaluate the inherent and after cyclic loading fracture strength of implant‐supported cantilevered fixed prostheses fabricated from recently introduced additively manufactured (AM) and subtractively manufactured (SM) materials, considering variations in prosthesis height.
Mustafa Borga Dönmez, Paola Maldonado, Çiğdem Kahveci, Ahmet Orgev, Marta Revilla‐León, Burak Yilmaz, Gülce Cakmak   +6 more
wiley   +1 more source