Results 61 to 70 of about 5,269 (220)

Workflow to facilitate complete denture scanning with an intraoral scanner: A technique report

Journal of Prosthodontics, EarlyView.
Abstract Scanning a denture with an intraoral scanner is typically more challenging than scanning a dentate arch. This article describes a novel technique for digitally duplicating a complete denture. The workflow involves scanning an existing denture using an intraoral scanner with the addition of specific markers and subsequently constructing a ...
Jiayi Yu, Jiayi Lu, Berna Saglik, Junying Li   +3 more
wiley   +1 more source

Effect of computer-aided designing/computer-aided manufacturing and 3D-printing fabrication techniques on marginal fit and internal gap of provisional restoration: A randomized clinical trial

Journal of Orofacial Sciences
Introduction Provisional restoration for long-term implant-supported prosthesis and fixed partial denture requires accurate fit for durability.
Sanjay Kumar Sukumar, Ahila Singaravel Chidambaranathan, Muthu Kumar Balasubramanium   +2 more
doaj   +1 more source

ORTHODONTIC AND ORTHOPEDIC REHABILITATION OF PATIENTS WITH CLEFT OF UPPER LIP, ALVEOLAR SURGERY, HARD AND SOFT PALATE

Український стоматологічний альманах, 2018
The problem of children’s rehabilitation with cleft palate is multi edged and complex. The ultimate goal of rehabilitation measures is to restore the anatomical integrity of the tissues of the hard and soft palate, the function of the articulatory and ...
O.M. Makarova, M.V. Semenyaka, G.M. Balya, V.D. Kuroyedova   +3 more
doaj   +1 more source

Impact of monomer contamination of isopropanol during post‐rinsing on the accuracy of dental models fabricated by vat photopolymerization

Journal of Prosthodontics, EarlyView.
Abstract Purpose The aim of this study was to investigate the impact of an increasing level of monomer contamination of isopropanol (isopropyl alcohol [IPA]) during post‐rinsing on the dimensional stability of test samples produced by vat photopolymerization.
Florian Flierl, Benedikt C. Spies, Severin Rothlauf, Kirstin Vach, Ralf J. Kohal, Jörg Lüchtenborg   +5 more
wiley   +1 more source

Influence of Matrix Type on Surface Roughness of Three Resins for Provisional Crowns and Fixed Partial Dentures [PDF]

, 2017
Purpose: This study evaluated the effect of matrix type on the surface roughness of resins for provisional crowns and fixed partial dentures. Materials and methods: Ninety specimens of two acrylic resins (Trim II, Tab2000) and one bis-acryl composite ...
Ayuso Montero, Raúl, Lujan-Climent, Mar, Martínez Gomis, Jordi, Peraire Ardèvol, Maria, Salsench Cabré, Juan   +4 more
core   +1 more source

Influence of different manufacturing materials on the accuracy and fitting of full‐arch restorations using a photogrammetry scanner—In vitro study

Journal of Prosthodontics, EarlyView.
Abstract Purpose This study aimed to assess the accuracy of a photogrammetry scanner and evaluate the influence of four different manufacturing materials on the accuracy and fitting of full‐arch restorations made using a photogrammetry scanner. Materials and Methods A cast with six implant abutment analogs was made.
Paulo Sergio Borella, Abidiel Silva Guimaraes, Thais Silva Mendonça, Gus Khalil, Sandra Al‐Tarawneh, Lyndon F. Cooper, Gustavo Mendonça   +6 more
wiley   +1 more source

Transition from being OK to NOT OK with tooth loss among a selection of older people in Iran: a qualitative study [PDF]

, 2016
Background: Several studies have covered oral health and dental decay in old age, but these studies mostly applied standard quantitative tools and did not include consideration of older people’s views on oral problems, partial edentulism in particular.
Andrade, Bianco, Bratu, Brondani, Burns, Carr, Casotti, Davis, De Marchi, Eliopoulos, Ettinger, Graneheim, Gregory, Heinonen, Holloway, Johannsen, Khadem, Khan, Kikutani, Kneckt, Käyser, Lee, Lexomboon, Lopez-Jornet, Mariño, McGarry, Modanloo, Moshref, Müller, Niesten, Ozkan, Polit, Saintrain, Srisilapanan, Thomson, Zarb   +35 more
core   +2 more sources

Effects of printing temperature and post‐curing duration on the dimensional reproducibility and fracture load of 3D‐printed dental prostheses: An exploratory study

Journal of Prosthodontics, EarlyView.
Abstract Purpose This in vitro study aimed to evaluate the effects of printing temperature and post‐curing duration on the dimensional reproducibility and mechanical properties of three‐dimensional (3D)–printed dental prostheses. Materials and Methods Photopolymer specimens were fabricated using a stereolithographic 3D printer at two temperatures: room
Ji‐Min Lee, KeunBaDa Son, Kyu‐Bok Lee   +2 more
wiley   +1 more source

Prevalence and morphological variability of torus palatanus and torus mandibularis [PDF]

, 2014
Background: The oral tori are non-pathological and benign exostosis of the cortical and limited amount of bone marrow, covered with a thin and poorly vascularized mucosa.
Becker, Holger, Goossens, Herman, Haraldsson, Tommy, Hlawatsch, Nadine, Lind, Anders, Malhotra-Kumar, Surbi, Turlej-Rogacka, Agata, van der Wijngaart, Wouter   +7 more
core   +1 more source

Optimizing Anterior Implant Outcome Immediately After Implant Placement and Grafting by Using Patient’s Extracted Teeth: A Case Report [PDF]

, 2017
Optimizing anterior implant outcome using patient’s extracted teeth. Successful implant treatment in the anterior maxilla is predicated on providing a functional and esthetically acceptable outcome.
Banez, Jay Darryl, Bompolaki, Despoina, Hart, Yvonne, Prasad, Soni   +3 more
core   +1 more source