Results 221 to 230 of about 89,414 (345)

Effect of cleft palate type and manufacturing method on feeding plate adaptation: A volumetric micro‐computed tomography analysis

Journal of Prosthodontics, EarlyView.
Abstract Purpose Feeding plates for cleft palate patients have been used by clinicians for many years to temporarily close the oro‐nasal communication until definitive treatment with surgical techniques. The current in vitro study aimed to evaluate the adaptation of the feeding plates manufactured by two different techniques for three cleft types ...
Osman Akıncı, Ece İrem Oğuz, Poyzan Bozkurt, Merve Berika Kadıoğlu, Mert Ocak, Kaan Orhan, Reha Şükrü Kişnişçi   +6 more
wiley   +1 more source

Factors that contribute to the successful fabrication of CAD-CAM complete dentures. [PDF]

J Family Med Prim Care
Alsubaiy EF.
europepmc   +1 more source

Biomechanics of the implant‐supported full arch fixed complete denture manufactured by milling and injection techniques: An experimental and FEA study

Journal of Prosthodontics, EarlyView.
Abstract Purpose This study aims to characterize the mechanical properties of implant‐supported full arch fixed complete dentures manufactured by milling and injection techniques. Materials and Methods Twenty‐two samples with milling and injection manufacturing techniques were fabricated.
Mustafa Gürkan, Ovul Kumbuloglu, Makbule Heval Şahan, Mert Narin, Halis Kandaş, Yusuf Arman, Hasan Yildiz, Mahmut Pekedis   +7 more
wiley   +1 more source

Shear Bond Strength of Artificial Teeth to Conventional and Computer-Aided Design/Computer-Aided Manufacturing (CAD/CAM) Denture Bases: An In Vitro Comparison. [PDF]

Cureus
Rout S, Mittal R, Madan R, Rana V, Madan P, Sardar M, J K, Tyagi M, Gupta S.   +8 more
europepmc   +1 more source

Workflow to facilitate complete denture scanning with an intraoral scanner: A technique report

Journal of Prosthodontics, EarlyView.
Abstract Scanning a denture with an intraoral scanner is typically more challenging than scanning a dentate arch. This article describes a novel technique for digitally duplicating a complete denture. The workflow involves scanning an existing denture using an intraoral scanner with the addition of specific markers and subsequently constructing a ...
Jiayi Yu, Jiayi Lu, Berna Saglik, Junying Li   +3 more
wiley   +1 more source

A Comparison of Uptake of Tea Stains and Effectiveness of Denture Cleansers on CAD/CAM Versus Conventional Acrylic Denture Base.

J Pharm Bioallied Sci
Darwish M, Khan AS, Alanazi LM, Alenazi MM, Alassaf HS, Alharbi NM, Almutairi MM.   +6 more
europepmc   +1 more source

Impact of Printing Orientations on the Trueness and Precision of Additively Fabricated Complete Denture Base Before and After Thermal Aging. [PDF]

Dent J (Basel)
Al-Zayyat ST, Alshehri T, Alameer ST, Althunayyan SH, Aldhafiri RA, Albasry Z, Balhaddad AA, Alalawi H, Gad MM.   +8 more
europepmc   +1 more source

Evaluation of Bond Strength and Dimensional Accuracy of Soft Liner to Microwave Cured Denture Base Material

, 2020
Shilan H Fatah, Radhwan Hasan
openalex   +2 more sources

Shade variability and stability in interim and definitive tooth‐colored resin‐based restorative materials: Comparing manufacturer‐claimed shades to a universal shade guide

Journal of Prosthodontics, EarlyView.
Abstract Purpose To evaluate the shade variability and stability of interim and definitive tooth‐colored restorative materials by comparing manufacturer‐claimed shades to a universal shade guide before and after thermocycling. Materials and Methods Eight commercially available tooth‐colored restorative materials were tested, including conventional ...
Amal Alfaraj, Toshiki Nagai, Wei‐Shao Lin   +2 more
wiley   +1 more source

Clinical Management of Worn Ball Abutments in Mandibular Mini-Implant Overdentures: A Case Report in a Skeletal Class II Patient. [PDF]

Dent J (Basel)
Murariu-Măgureanu C, Preoteasa E, Teodorescu C, Preoteasa CT.   +3 more
europepmc   +1 more source