Systematic review and meta analysis of mechanical properties of 3D printed denture bases compared to milled and conventional materials [PDF]
Scientific ReportsDenture base fabrication has advanced with the introduction of computer-aided design and manufacturing (CAD-CAM) techniques, such as subtractive milling and additive 3D printing.
Amr Azab +2 more
exaly +3 more sources
How Does the Bonding Strength of Reline Materials and Denture Teeth Vary Between 3D‐Printed and Milled Complete Denture Bases? A Systematic Review and Meta‐Analysis [PDF]
Clinical and Experimental Dental ResearchObjective To systematically compare the bond strength of denture teeth and reline materials to additively manufactured (AM) versus subtractively milled (SM) denture base resins and to identify the material‐ and process‐related factors influencing bonding
Seyed Ali Mosaddad +2 more
exaly +3 more sources
Do 3D-Printed and Milled Denture Bases Differ in Microbial Activity and Adhesion? A Systematic Review and Meta-Analysis [PDF]
International Dental JournalThe increasing adoption of digital manufacturing in prosthodontics raises concerns about microbial metabolic activity and adhesion on denture bases fabricated via additive and subtractive methods.
Seyed Ali Mosaddad +2 more
exaly +4 more sources
Accuracy of Digitally Fabricated Wax Denture Bases and Conventional Completed Complete Dentures [PDF]
Dentistry Journal, 2017 The purpose of this investigation was to analyze the accuracy of digitally fabricated wax trial dentures and conventionally finalized complete dentures in comparison to a surface tessellation language (STL)-dataset.
Bogna Stawarczyk, Marlis Eichberger
exaly +4 more sources
CAD-CAM vs. conventional denture bases: a systematic review with network meta-analysis of in vitro studies comparing strength, hardness, toughness, and elastic properties [PDF]
Frontiers in Dental MedicineBackgroundScientific evidence from in vitro studies comparing the mechanical properties of dentures fabricated with computer-aided design-computer-aided manufacturing (CAD-CAM) and conventional techniques is inconclusive. This systematic review with meta-
Rohit Kunnath Menon +5 more
doaj +2 more sources
Strain gauge analysis and deformation detection of maxillary denture bases reinforced by CAD/CAM milled zirconia and cobalt chromium (Co-Cr) frameworks: An in-vitro study [PDF]
BMC Oral HealthBackground A lot of studies have demonstrated the increased hardness of the reinforced maxillary dentures. However, the amount of stress induced by different reinforcement materials under the reinforcement dentures and their effect on the underlying ...
Maha Nagy Mohamed Kamal +3 more
doaj +2 more sources
Influence of CAD/CAM Technology on the Accuracy of Complete Denture Bases
Journal of Pharmacy and Bioallied SciencesBackground: “By making entire denture fabrication more efficient and accurate, computer-aided design and manufacturing (CAD/CAM) technology has changed prosthodontics forever.” The purpose of this research was to compare the correctness of full denture ...
Maryam M. AlRasheedi, Fatemah B. Ibrahem
doaj +2 more sources
Effect of mechanical and chemical surface treatments on the repairing of milled and 3D-printed denture bases [PDF]
Scientific ReportsEnsuring a strong bond between chairside autopolymerized acrylic resin to denture base is essential for denture repair and reline procedures. However, there is no established protocol to enhance bond strength between autopolymerizing resin and computer ...
Hein Linn Htat +4 more
doaj +2 more sources
Four Different Build Angles in 3D-Printed Complete Denture Bases: A Comparative In Vitro Study
Applied Sciences (Switzerland)In this study, we aimed to investigate the differences in tissue surface adaptation and the variations in distances between reference points on the polished surfaces of 3D-printed denture bases produced at different build angles. The build angles were 0°,
Yong-Sang Lee +2 more
exaly +3 more sources
ProceedingsMicrobial colonization of denture bases plays a key role in the development of denture stomatitis and other oral conditions, with Candida albicans being the main etiologic agent [...]
Meda-Lavinia Negrutiu +2 more
exaly +3 more sources