Results 241 to 250 of about 1,726,979 (337)

Molecular Biointerface Characterization for an Implanted Medical Device Using Cryogenic Orbitrap Secondary Ion Mass Spectrometry (Cryo-OrbiSIMS). [PDF]

ACS Appl Mater Interfaces
Bin Sabri AH, Wong KFC, Kotowska AM, Fisher LE, Luckett J, Mase JM, Kämmerling L, Figueredo G, Scurr DJ, Ghaemmaghami AM, Alexander MR.   +10 more
europepmc   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

Longus colli calcific tendinitis, an uncommon cause of neck pain. A short series of cases and review of literature. [PDF]

Int Orthop
Combalia A, Zelada-Castro K, Alemany X, Vargas-Reverón C, Muñoz-Mahamud E.   +4 more
europepmc   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

Optimization of selective catalytic reduction for nox emission control: an experimental and CFD analysis of mixer designs. [PDF]

Sci Rep
Bandaru S, Jayaraman J, Vijetha K, Kumar A, Hariharan G, Mohan M, Sharma A, Singh HR.   +7 more
europepmc   +1 more source

Microstructure of deposited layer in TiC-Mo2C-Ni cermet coated with TiC by CVD process.

, 1986
Nobujiro Tuchiya, Osamu Terada, Kôji Hayashi   +2 more
openalex   +2 more sources

Interactions between Molten High‐Silicon Electrical Steels and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
This study examines how several molten high‐silicon electrical steels interact with both conventional and recycled MgO–C refractories. For this, various immersion experiments are conducted. In addition to infiltration, a number of mechanisms are identified and explained that control the corrosion of the refractory material.
Lukas Neubert, Matheus Roberto Bellé, Anton Yehorov, Anhelina Mospan, Till M. J. Stadtmüller, Seetharaman Sridhar, Christos G. Aneziris, Olena Volkova   +7 more
wiley   +1 more source

Where Is the Filler? Magnetic Resonance Imaging Reveals Hidden Hyaluronic Acid in a Delayed Chin Complication. [PDF]

Plast Reconstr Surg Glob Open
Mariluis CA, Lagonegro D, Cavallieri F, Barrera P.   +3 more
europepmc   +1 more source

Prediction of Surface Topography Parameters in Direct Laser Interference Patterning of Stainless Steel Using Infrared Monitoring and Convolutional Neural Networks

Advanced Engineering Materials, EarlyView.
This study presents an infrared monitoring approach for direct laser interference patterning (DLIP) combined with a convolutional neural network (CNN). Thermal emission data captured during structuring are used to predict surface topography parameters.
Lukas Olawsky, Marcelo Sallese, Leander Kläber, Clemens Kuhn, Keming Du, Andrés Fabián Lasagni   +5 more
wiley   +1 more source

Fractal modeling of Baba Ali iron ore deposit geophysical data in western Iran for magnetic anomaly separation in GIS environment. [PDF]

Sci Rep
Seyedrahimi-Niaraq M, Shahsavani H.
europepmc   +1 more source