Results 51 to 60 of about 603,582 (234)

Stability and Synthesis of Phospholipids during Desiccation and Rehydration of a Desiccation-Tolerant and a Desiccation-Intolerant Moss [PDF]

Plant Physiology, 1982
The fatty acid composition of the phospholipids from the desiccation-tolerant moss Tortula ruralis (Hedw.) Gaertn, Meyer and Scherb and the desiccation-intolerant moss Cratoneuron filicinum has been determined. No changes in composition occur in either moss as a consequence of rapid drying, but, after slow drying, there is a decline in some unsaturated
R R, Stewart, J D, Bewley
openaire   +2 more sources

Low‐Temperature Imidization of Polyimides (PI) for Scalable Manufacturing of Flexible Wearable Electronics

Advanced Engineering Materials, EarlyView.
Low‐temperature imidization of PEG‐modified polyimide enables fully screen‐printed, roll‐to‐roll fabrication of flexible electrodes on PET substrates, delivering robust mechanical durability and reliable ECG/EMG signal performance for wearable electronics.
Akib Abdullah Khan, Jong‐Hoon Kim
wiley   +1 more source

Exogenous K+ enhances the desiccation tolerance and adhesion of Pseudomonas protegens SN15-2

Frontiers in Microbiology
IntroductionPseudomonas protegens is an important plant growth-promoting rhizobacterium capable of both suppressing phytopathogens and enhancing plant growth. The ability of P.
Jian Wang, Yaping Wang, Shufeng Bi, Wei Wang   +3 more
doaj   +1 more source

Inverse Identification of Energy‐Dependent Laser Absorptivity in NiTi Laser Powder‐Bed Fusion via Calibrated Melt Pool Simulation

Advanced Engineering Materials, EarlyView.
A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi, Hadi Moutablaleh, Ignatius A. Setiawan, Mehrshad Mehrpouya   +3 more
wiley   +1 more source

Desiccation of rock pool habitats and its influence onpopulation persistence in a Daphnia metacommunity [PDF]

, 2009
Habitat instability has an important influence on species' occurrence and community composition. For freshwater arthropods that occur in ephemeral rock pools, the most drastic habitat instabilities are droughts and the intermittent availability of water.
Pajunen, I., Ebert, Dieter, Dieter Ebert, Altermatt, Florian, Pajunen, V. Ilmari, V. Ilmari Pajunen, Altermatt, F., Ebert Dieter, Pajunen V. Ilmari, Altermatt Florian, V Ilmari Pajunen, Florian Altermatt   +11 more
core   +2 more sources

Characterization of polyphenols in leaves of four desiccation tolerant plant families [PDF]

, 2005
Includes bibliographical references.Polyphenols in plants are known to act as antioxidants, antimicrobials, antifungal, photoreceptors, visual attractors and as light screens.
Dzobo, Kevin
core   +1 more source

Irreversibility of the cell wall modification acts as a limiting factor in desiccation tolerance of Oryza sativa ssp. Indica cv MR303

Plant Stress
Desiccation tolerance has emerged as a potential strategy for crop improvement. However, the application of desiccation tolerance in crops, particularly rice, has been challenging and limited. Studies in angiosperms suggest that desiccation in vegetative
Iqmal Asyraf Ilias, Alina Wagiran, Kamalrul Azlan Azizan, Ismanizan Ismail, Abdul Fatah A. Samad   +4 more
doaj   +1 more source

Superlubricity and Corrosion Inhibition Properties of Solvate Ionic Liquids in Hybrid Carbon Fiber Reinforced Plastic–Steel Interfaces

Advanced Engineering Materials, EarlyView.
Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees, Timothy Harte, Bhagya Dharmasiri, Y. Athulya Wickramasingha, David J. Hayne, Daniel J. Eyckens, Luke C. Henderson   +6 more
wiley   +1 more source

Adaptive Foam 3D Printing of Ultralight and Multifunctional Materials

Advanced Engineering Materials, EarlyView.
Adaptive foam 3D printing, enabled by expandable microspheres, imparts cellular structures to thermoplastic and thermosetting polymers, manufactured through a variety of processes including fused filament fabrication, direct ink writing, digital light processing, and inkjet printing.
Nariman Rajabifar, Amir Ameli
wiley   +1 more source

Cas9-mediated genome editing reveals a significant contribution of calcium signaling pathways to anhydrobiosis in Pv11 cells

Scientific Reports, 2021
Pv11 is an insect cell line established from the midge Polypedilum vanderplanki, whose larval form exhibits an extreme desiccation tolerance known as anhydrobiosis.
Yugo Miyata, Hiroto Fuse, Shoko Tokumoto, Yusuke Hiki, Ruslan Deviatiiarov, Yuki Yoshida, Takahiro G. Yamada, Richard Cornette, Oleg Gusev, Elena Shagimardanova, Akira Funahashi, Takahiro Kikawada   +11 more
doaj   +1 more source