Results 171 to 180 of about 1,313,219 (266)

Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning

Advanced Engineering Materials, EarlyView.
The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley   +1 more source

Gallium Microalloying in Bi–Sn Solders: Interfacial Phase Formation, Wettability, and Long‐Term Shear Reliability Under Isothermal Aging

Advanced Engineering Materials, EarlyView.
Gallium microalloying redirects interfacial reactions in low‐temperature Bi–Sn solders from Cu–Sn toward Cu–Ga intermetallic formation. The resulting Cu–Ga layer suppresses intermetallic growth during thermal aging, alters fracture pathways, and improves interfacial stability.
Iva Králová, Markéta Klimtová, Mohd Faizul Mohd Sabri, Yew Hoong Wong, Petr Veselý, Martin Plaček, Karel Dušek   +6 more
wiley   +1 more source

Toward Full Interoperability in Materials Science: Integrating Workflows With Knowledge Graphs

Advanced Engineering Materials, EarlyView.
The connection of conceptual workflow design, portable execution, and ontology‐based semantics leading to provenance‐rich knowledge graphs are main contributors to interoperability in materials science and a prerequisite to AI‐assisted orchestration and for interoperable Materials Acceleration Platforms.
Jan Janssen, Osamu Waseda, Bernd Bayerlein, Simon Stier, Steffen Brinckmann, Abril Azócar Guzmán, Sarath Menon, Matthias A. Popp, Jesper R. Pedersen, Ivano E. Castelli, Jörg Waitelonis, Wolfgang Wenzel, Jörg Neugebauer, Jörg Schaarschmidt, Tilmann Hickel   +14 more
wiley   +1 more source

Effects of Mg on Microstructure and Solidification of a Hypereutectic Zn–8 wt.%Al Alloy

Advanced Engineering Materials, EarlyView.
An appreciable set of results involving thermal data, microstructure, chemical composition, and microstructural growth laws is reported for ZnAlMg alloys. Such results demonstrate that ZnAlMg alloys have high potential for applications in automotive self‐lubricating components, batteries, and electrical systems.
Raí B. de Sousa, Jeverton L. Paixão, Daylla S. Silva, Bruno S. Sobral, Mucio D. de Medeiros, José E. Spinelli, Bismarck L. Silva   +6 more
wiley   +1 more source

Validation of a Novel, Low-Cost, Portable MRI-Compatible Exercise Device in Healthy Volunteers and Patients With Pulmonary Hypertension. [PDF]

NMR Biomed
Virsinskaite R, Brown JT, Kotecha T, Bower D, Steeden JA, Montalt-Tordera J, Jaubert O, Fontana M, Coghlan JG, Knight DS, Muthurangu V.   +10 more
europepmc   +1 more source

FastNano Liquid: An Automated Platform for Small‐Angle X‐ray Scattering‐Based Materials Discovery

Advanced Engineering Materials, EarlyView.
We present FastNano Liquid, an automated small‐ and wide‐angle X‐ray scattering platform for the combined synthesis and characterization of (nano)materials. The platform is coupled to varied reactor workflows for both in situ studies of reaction kinetics and ex situ screening of synthesis conditions to support machine learning‐guided exploration ...
Pierre‐Baptiste Flandrin, Émeline Cournède, Jens Krarup, Michael Lesa, Foyzul Hasan, Amandine Séné, Arnaud Lahouati, David Benhaiem, Jérémie‐Luc Sanchez, Simon Delacroix, Thierry Gacoin, Fabienne Testard, Damien Faivre, David Carriere, Corinne Chevallard, Olivier Taché, Mark A. Levenstein   +16 more
wiley   +1 more source

A Novel Device for Pulmonary Expansion Under Simulated Healthy and Neuromuscular Conditions: A Bench Simulation Study. [PDF]

Med Devices (Auckl)
Dorça AC, Morais LA.
europepmc   +1 more source

3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement

Advanced Engineering Materials, EarlyView.
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin, Gloria R. Young, Francesca Tallia, Reece N. Oosterbeek, Shaaz Ghouse, Edward Spiers, Nupur Kohli, Tom Briggs, Marc Masen, Siwei Li, Ren‐Jei Chung, Jonathan R. T. Jeffers, Julian R. Jones   +12 more
wiley   +1 more source

Rotary 3D Printing With Integrated Electroplating

Advanced Engineering Materials, EarlyView.
A rotary material extrusion platform integrates localized copper electroplating with printing and encapsulation to fabricate cylindrical polymer–metal structures containing fully embedded, low‐resistance conductive pathways that enable internal Joule heating and thermally activated shape‐memory responses.
Antonio Zagaria, Nicola Larovere, Moslem Mohammadi, Gianluca Percoco, Ali Zolfagharian, Gianni Stano   +5 more
wiley   +1 more source

Comparison of Sizing Methods to Optimize Device Selection for Percutaneous Closure of Atrial Septal Defects. [PDF]

Cardiol Res Pract
Vural Ç, Baykan A, Doğan A, Kum YE, Akay ÖP, Üzüm K, Narin N.   +6 more
europepmc   +1 more source