Results 61 to 70 of about 197,569 (311)
Microstructure characterization and corrosion resistance properties of Pb-Sb alloys for lead acid battery spine produced by different casting methods. [PDF]
PLoS ONE, 2018 The aim of this study is to find out the microstructure, hardness, and corrosion resistance of Pb-5%Sb spine alloy. The alloy has been produced by high pressure die casting (HPDC), medium pressure die casting (AS) and low pressure die casting (GS ...
Asiful H Seikh +5 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé +5 more
wiley +1 more source
A Network Technique for Analysis of the Thermal Transient Casting Process [PDF]
, 1996 A network approach to simulating the thermal transient casting process is presented and compared with experimental data and a continuum finite element model. For a sufficiently fine network, all comparisons are good.
Gathin, David T., Sulaiman, Shamsudin
core
Zein‐Based Adhesives: Sustainable Extraction and Application in Bioadhesive Technologies
Advanced Engineering Materials, EarlyView.Zein is extracted from corn gluten meal using a simple and scalable process with high yield (~90%). The resulting protein is applied in bioadhesives modified with Ca2+ and Fe3+ ions, exhibiting substrate‐dependent adhesion. The findings demonstrate competitive bonding performance and highlight the role of ionic interactions in tuning adhesion ...
Paula Bertolino Sanvezzo +3 more
wiley +1 more source
Journal of Japan Institute of Light Metals, 2019 PROBLEM TO BE SOLVED: To provide a die casting machine capable of consistently producing excellent castings by adequately detecting a change in the molten metal supply amount. SOLUTION: The die casting machine 1 includes a ladle 23 for pouring ladled molten metal ML into an injection sleeve 7, a deposition sensor 29 for detecting the deposition state ...
openaire +2 more sources
Semisolid processing characteristics of AM series Mg alloys by rheo-diecasting [PDF]
, 2006 The official published version of this Article can be found at the link below - Copyright @ 2006 ASM InternationalAn investigation has been made into the solidification behavior and microstructural evolution of AM50, AM70, and AM90 alloys during rheo ...
A. Das +22 more
core +1 more source
Advanced Engineering Materials, EarlyView.The thermal diffusivity of MgO‐C refractories is highly sensitive to sample preparation and processing procedures. In this article, the effects of coking sequence, machining conditions, structural inhomogeneity, and graphite coating application on measurements using laser flash apparatus are systematically investigated.
Luyao Pan +4 more
wiley +1 more source
New Development of Research on Die Steel for Die-Casting Steel in China
Teshugang, 2022 The research and application achievements of die casting steel materials in China are introduced.By studying the influence of alloying elements on material properties of die material, a new die casting die steel with low Si, V and Ni, CO and W has been ...
雷应华 +4 more
doaj
Microstructural characterisation and thermal stability of an Mg-Al-Sr alloy prepared by rheo-diecasting [PDF]
, 2007 A commercial Mg-6Al-2Sr (AJ62) alloy has been prepared by a semisolid rheo-diecasting (RDC) process. The microstructure of the RDC alloy exhibits typical semisolid solidification features, i.e., 8.4 vol% primary α-Mg globules (23 μm in diameter), formed ...
Fan, Z, Liu, G, Wang, F, Wang, Y
core