Results 231 to 240 of about 30,233 (313)

A lab-scale biofiltration system for mitigating diluted methane emissions. [PDF]

HardwareX
Geiger T, González C, Ali J, Vasco-Correa J.   +3 more
europepmc   +1 more source

Carboxylic‐Acid Functionalized Multiwalled Carbon Nanotube‐Alkane‐Based Resistive Temperature Sensor for Cold Chain Applications

Advanced Engineering Materials, EarlyView.
This study presents a reversible temperature sensor with high switching ratio, ∼103. The device is fabricated using PET‐ITO and carbon nanotube dispersions in alkane. Considering its application in cold chain logistics, a proof‐of‐concept with LED is showcased. Thus, a temperature drop below the threshold temperature (crystallization temperature of the
Sunil Kumar Behera, Philippe Marrec, A. Jorge Parola, Madalena Dionísio, Hugo Águas, Andreia F. M. Santos, Hamed Pourkheirollah, Donald Lupo, César A. T. Laia   +8 more
wiley   +1 more source

Multiscale investigation of cavitation surge characteristics in the swirling flow using Eulerian-Lagrangian method. [PDF]

Ultrason Sonochem
Wang Z, Liu D, Ji B, Luo X.
europepmc   +1 more source

Low‐Cost, Large‐Scale Nanoporous Metals by Mechanical Alloying, Oxide Reduction, and Dealloying of Powders

Advanced Engineering Materials, EarlyView.
Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley   +1 more source

Light scattering-based screening method for rapid evaluating antibiotic effects on bacteria using laser speckle imaging. [PDF]

J Biol Eng
Kim D, Moon S, Lee J, Cho K, Lee C, Yoon J.   +5 more
europepmc   +1 more source

Re-analysis of GOME/ERS-2 Diffuser properties

, 2004
Aberle, Bernd, Wahl, Sandra, Slijkhuis, Sander, Loyola, Diego   +3 more
core  

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

Numerical study on the evolution of cavitating flow and collapse-induced erosion characteristics in high-speed hydraulic tunnel. [PDF]

Ultrason Sonochem
Liu B, Yu H, Yin Z, Zhang X.
europepmc   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

High-precision transdermal drug delivery enabled by a dual-pump parallel valveless piezoelectric micropump integrated with hollow microneedles. [PDF]

Microsyst Nanoeng
Zhang L, Sha W, Li Y, Chen X, Liu L, Hu H, Song J, Liang J, Zhang J.   +8 more
europepmc   +1 more source