Results 121 to 130 of about 3,165,974 (241)
Advanced Engineering Materials, EarlyView.A high interstital austenitic steel is additively manufactured and postdensified by HIP to eliminate gas porosity. Thereby, the loss of N and Mn in Ar HIP atmosphere is investigated. Further, HIP using N2 atmosphere is investigated which led to excessive nitride formation.
F. Großwendt +4 more
wiley +1 more source
Effective diffusion tensor computed by homogenization [PDF]
, 2013 The convergence of the long-time apparent diffusion tensor of diffusion magnetic resonance imaging (dMRI) to the effective diffusion tensor obtained by mathematical homogenization theory was considered for two-compartment geometric models containing non ...
Grebenkov, Denis +4 more
core +1 more source
Pore-Scale Modeling of Liquid Water Transport in Compressed Gas Diffusion Layer of Proton Exchange Membrane Fuel Cells Considering Fiber Anisotropy. [PDF]
Membranes (Basel), 2023 Wang H +5 more
europepmc +1 more source
Advanced Engineering Materials, EarlyView.PUF/ENB microcapsules were synthesized based on a sequential factorial design and incorporated into an epoxy matrix. Their anticorrosive action, associated with the self‐healing mechanism, demonstrated that the addition of microcapsules to the coating improved anticorrosive performance compared to pure epoxy coatings, particularly when the encapsulate ...
Vandicleya Alves Moreira +6 more
wiley +1 more source
Microstructure and properties of TiVNbTa/Inconel 600 diffusion welded joint
Cailiao gongchengIn view of the excellent corrosion resistance and high temperature strength of TiVNbTa refractory high entropy alloy, and the potential application prospect of the TiVNbTa RHEA/Inconel 600 joining component, the diffusion bonding properties were studied.
LI Juan +6 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Additive manufacturing introduces pronounced microstructural and crystallographic anisotropy in Ni‐based superalloys, resulting in orientation‐dependent creep deformation and damage. This review identifies the key microstructural origins of creep anisotropy, examines their influence on dominant deformation mechanisms, and highlights processing ...
Chandan Kumar +3 more
wiley +1 more source
Electrodeposition in Structural Lattices of Variable Architectures
Advanced Engineering Materials, EarlyView.Electrodeposition enables geometry‐sensitive, autonomous void filling while simultaneously tuning chemical and mechanical properties. The development of approaches that can autonomously fill and heal material voids and yield composites with tailorable properties is increasingly relevant in engineering.
Yeong‐Man Kwon +3 more
wiley +1 more source
Diffusion imaging of the brain: technical considerations and practical applications [PDF]
, 2005 This chapter presents a brief introduction to the application of diffusion-weighted magnetic resonance imaging (MRI) to in vivo studies. Diffusion-weighted MRI has found application both in the clinic, and in basic neuroscience.
Norris, David G.
core
Advanced Engineering Materials, EarlyView.Additively manufactured AlCrFe2Ni2 with contrasting BCC/B2‐dominant and lamellar FCC + BCC/B2 microstructures exhibits the same pressure‐induced BCC/B2 → HCP transformation. Under laser heating at high pressure, HCP is destabilized, and a cubic BCC/B2 + FCC assemblage is recovered, while the lower‐scan‐speed microstructure transforms at a lower ...
Raimundas Sereika +5 more
wiley +1 more source
The cross-interactions in the Ni/Sn/Cu diffusion couples with an electrolesspalladium surface finish
, 2014 Four diffusion couples, Ni/Pd/Sn, Ni/Pd/Sn/Cu, Cu/Pd/Sn, and Cu/Pd/Sn/Ni, were prepared by hot pressingand the interfacial reactions in these multi-layer structures aged at 200 C were investigated.
Chi-Pu Lin, Chih-Ming Chen
core