Results 141 to 150 of about 383,988 (304)

Packaging of Macroscopic Material Payloads: Needs, Challenges, Concepts, and Future Directions

Advanced Engineering Materials, EarlyView.
This review introduces a unified framework that decomposes any macroscopic packaging system into the payload, packaging material, and packaging strategy and combines them into a conceptual packaging equation: packaging strategy = payload + packaging material.
Venkata S. R. Jampani, Manos Anyfantakis
wiley   +1 more source

Synthesis of a Novel Thermoresponsive S53P4 Bioactive Glass Extract–Poloxamer 407 Injectable Hydrogels: Assessment of Biocompatibility and Antimicrobial Properties

Advanced Engineering Materials, EarlyView.
This study investigates innovative thermoreversible hydrogels derived from S53P4 bioactive glass extracts to aid in the healing of infected diabetic foot wounds. These injectable gels, which gel at body temperature, release beneficial ions and remain stable over time.
Marian G. Vargas Guerrero, Adrian Stiller, Alex Nygård, Matej Krivulka, Lars Galema, Erwin Peters, Jimmy Lucchesi, Peter Uppstu, Leena Hupa, Jacobus J. C. Arts   +9 more
wiley   +1 more source

Digital Elevation Models (Experimental Bed)

, 2018
Digital Elevation Models from Bed Scans used in the following paper: Elgueta-Astaburuaga and Hassan, Sediment storage, partial transport, and the evolution of an experimental gravel bed under changing sediment supply regimes, submitted to Geomorphology in 2018. Each DEM name specifies the run R(1-7) in which it was collected and time H(1-40).
openaire   +1 more source

On the Influence of Antioxidants and Recycled MgO–C Source Material on the Mechanical Properties of Carbon‐Bonded Magnesia Refractories

Advanced Engineering Materials, EarlyView.
The presented study focuses on the fracture behaviour of carbon‐bonded magnesia MgO–C refractories, where environmentally friendly fructose, collagen and lignin serve as temporary binding agents. The partial substitution of the source material with recycled MgO–C reduces the fracture resistance, which can be counteracted by the additional introduction ...
Marc Neumann, Tom Weber, Jana Hubálková, Florian Kerber, Dinesh Kumar Gunasekar, Hans Jelitto, Christos G. Aneziris   +6 more
wiley   +1 more source

Unit 38 - Digital Elevation Models

, 1990
This unit considers digital elevation models (DEMs) as one way of representing surfaces. It describes how DEMs are created and used, particularly in hydrology. Approaches for estimating elevation, slope and aspect, and for determining drainage networks are presented, along with a discussion of issues that may arise when automatically determining ...
Unit 38, CC in GIS, Klinkenberg, Brian
openaire   +1 more source

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

Advanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm, Lukas Knöchel, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +5 more
wiley   +1 more source

Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger, Lienhard Wegewitz, Wolfgang Maus‐Friedrichs   +2 more
wiley   +1 more source

Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V

Advanced Engineering Materials, EarlyView.
Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena, Benjamin Bergmann, Michael Zenger   +2 more
wiley   +1 more source

Evaluating Energy Absorption Performance of Filled Lattice Structures

Advanced Engineering Materials, EarlyView.
Maximum stress must be considered to robustly evaluate energy absorber designs. This approach was applied to compare all types of absorbers in a single Ashby diagram and determine the utility of filling lattice voids with a second material. High‐performance fillers can improve the performance of lattices that are limited by buckling or catastrophic ...
Christian Bonney, William P. King, Iwona Jasiuk   +2 more
wiley   +1 more source

Single beam echo-sounding dataset and digital elevation model of the southeastern part of the Baltic Sea (Russian sector). [PDF]

Data Brief, 2019
Dorokhov D, Dudkov I, Sivkov V.
europepmc   +1 more source