Results 201 to 210 of about 5,255,523 (302)

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

State-amplified platform inequality: The economic geography of digital cultural policy in China. [PDF]

PLoS One
Su LD, Pang ZH, Tan ZH, Wen ZX, Ren M, Zhang Y.   +5 more
europepmc   +1 more source

NFDI MatWerk Ontology (MWO): A BFO‐Compliant Ontology for Research Data Management in Materials Science and Engineering

Advanced Engineering Materials, EarlyView.
This article presents the NFDI‐MatWerk Ontology (MWO), a Basic Formal Ontology‐based framework for interoperable research data management in materials science and engineering (MSE). Covering consortium structures, research data management resources, services, and instruments, MWO enables semantic integration, Findable, Accessible, Interoperable, and ...
Hossein Beygi Nasrabadi, Ebrahim Norouzi, Kostiantyn Hubaiev, Jörg Waitelonis, Harald Sack   +4 more
wiley   +1 more source

A case of non-functioning pituitary adenoma with calcification

Asian Journal of Surgery
Wen-Long Fang, Rui-Xiang Ge, Guang-Fu Di, Xiao-Chun Jiang   +3 more
doaj   +1 more source

HealthyPregnancy: development and feasibility of a digital care guide to promote recommended gestational weight gain in pregnant women living with overweight in Denmark. [PDF]

BMJ Open
Hansen MK, Bendix JM, Løkkegaard ECL, Schiøtz ML, Broberg L.   +4 more
europepmc   +1 more source

Characterization of Nitinol Produced by Laser Powder Bed Fusion for Mechanical Metamaterial Applications

Advanced Engineering Materials, EarlyView.
Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek, Jakub Hurník, Miroslav Šmíd, Ondřej Zobač, Melanie Todt, Daniel Koutný   +5 more
wiley   +1 more source

Informing NHS policy in ‘digital-first primary care’: a rapid evidence synthesis

, 2019
Rodgers M, Raine G, Thomas S, Harden M, Eastwood A.   +4 more
europepmc   +1 more source

The impact of trust in AI on digital innovation examining the moderation of intellectual capital and task characteristics. [PDF]

Sci Rep
Lin X, Wu C, Wang T, Sheng F.
europepmc   +1 more source

A Numerical–Experimental Approach for Multi‐Matrix Fiber‐Reinforced Plastics Characterization Using Finite Element Model Updating

Advanced Engineering Materials, EarlyView.
A numerical–experimental framework is developed for characterizing multi‐matrix fiber‐reinforced polymers (MM‐FRPs) combining epoxy and polyurethane matrices. Harmonic bending tests are integrated with finite element model updating (FEMU) to simultaneously identify elastic and viscoelastic material parameters.
Rodrigo M. Dartora, Tales V. Lisbôa, Axel Spickenheuer, Rogério J. Marczak, Jakson M. Vassoler   +4 more
wiley   +1 more source

Post-traumatic glioma: Report of one case

Asian Journal of Surgery
Yang Wang, Lean Sun, Guangfu Di, Xiaochun Jiang   +3 more
doaj   +1 more source