Results 151 to 160 of about 49,580,621 (240)
A simplified thermoplastic pultrusion model is developed to predict thermal fields in glass fiber/polyethylene terephthalate (GF/PET) composites with reduced computational cost. By combining effective material homogenization, validation against literature data, and Gaussian‐process‐based optimization, the study reveals how heating limits, pulling speed,
Elder Soares +3 more
wiley +1 more source
A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi +3 more
wiley +1 more source
Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading
This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev +2 more
wiley +1 more source
Impact of MgO Additions on the Oxidation Resistance and Compression Behavior of Vanadium Alloys
An increase in oxidation resistance at 600 °C is achieved for alloys containing more than 2.5 wt.% MgO. It has been established that, along with V2O5, MgO6V2, and Mg2O7V2 are formed, which are presumed to enhance oxidative stability. Furthermore, the possible transformation of Mg‐vanadates through reaction with CO2, which presumably occurs in this ...
Ievgen Solodkyi +5 more
wiley +1 more source
This article investigates the dependence of the properties on the manufacturing orientation in the form of the inclination angle to the build plate of LPBF‐fabricated NiTi rods with a diameter of 150–220 µm. Metallographic, chemical, thermal, and mechanical characterization show behavior under identical manufacturing conditions that ranges from ...
Sandra Herzig +2 more
wiley +1 more source
A Novel Approach to Estimate the Transition Temperature via Dynamic Nanoindentation
A new dynamic nanoindentation‐based method was developed that uses the stiffness ratio as an indicator of the elastic–plastic deformation contributions at different temperatures. The approach successfully identified transition temperatures in ferritic steel and distinguished them from continuously ductile austenitic steel.
Stefan Zeiler +4 more
wiley +1 more source
Electrodeposition in Structural Lattices of Variable Architectures
Electrodeposition enables geometry‐sensitive, autonomous void filling while simultaneously tuning chemical and mechanical properties. The development of approaches that can autonomously fill and heal material voids and yield composites with tailorable properties is increasingly relevant in engineering.
Yeong‐Man Kwon +3 more
wiley +1 more source
Microstructural evolution of premium rail steel during flash butt welding (FBW), comparing physically simulated heat‐affected zones with actual weld regions. Thermal cycles induce phase transformations and microstructural heterogeneity that influence weld quality and mechanical performance. These findings provide insights into optimizing FBW parameters
Emmanoelle Cintra da Cunha Araújo +15 more
wiley +1 more source
A thermoplastic PMMA‐based photoresin enables high‐resolution DLP printing followed by solvent‐vapor smoothing. The treatment reduces staircase‐induced surface roughness from 2.33 µm to 129 nm and increases visible‐light transmittance from approximately 30% to 80%, providing a route toward transparent PMMA components for rapid prototyping and non ...
Rozhin Heydarpour +5 more
wiley +1 more source
Gyroid Structured Globugraphite Carbon Foam With Hierarchical and Tailored Pore Size
Secondary sacrificial templates were designed and printed to create a defined network within a porous carbon. Lattices thermally degrades during the sintering process. Lattices are imprinted into the ceramic template and transferred to the morphology of Globugraphite.
Christiane Roller +6 more
wiley +1 more source

