Results 41 to 50 of about 5,034 (158)

The Fabrication of Micro Beam from Photopolymer by Digital Light Processing 3D Printing Technology

Micromachines, 2020
3D printing has lately received considerable critical attention for the fast fabrication of 3D structures to be utilized in various industrial applications.
Ishak Ertugrul
doaj   +1 more source

Influence of Solvent Type, Specimen Dimensions and Temperature on Chemical Debinding of Alumina Parts Fabricated Via Digital Light Processing [PDF]

Materials Research
Vat photopolymerization via digital light processing (DLP) enables the rapid fabrication of high-resolution ceramic components. However, careful post-processing is required to remove the hardened resin and consolidate the microstructure.
J. P. F. Matheus, A.P. Luz
doaj   +1 more source

Evaluation of 3D Printability and Biocompatibility of Microfluidic Resin for Fabrication of Solid Microneedles

Micromachines, 2022
In this study, we have employed Digital Light Processing (DLP) printing technology for the fabrication of solid microneedle (MN) arrays. Several arrays with various geometries, such as cones, three-sided pyramids and four-sided pyramids, with different ...
Atabak Ghanizadeh Tabriz, Beatriz Viegas, Michael Okereke, Md Jasim Uddin, Elena Arribas Lopez, Nazanin Zand, Medhavi Ranatunga, Giulia Getti, Dennis Douroumis   +8 more
doaj   +1 more source

Additive Manufacturing by Digital Light Processing (DLP)

, 2023
Additive Manufacturing (AM) or 3D printing is a process, based on different technologies, for the design and fabrication of three-dimensional objects, an alternative to conventional subtractive manufacturing. AM enables cost-effective manufacturing especially for complex geometries, potentially with lower environmental impacts compared to conventional ...
openaire   +1 more source

Embedding Polysaccharide Thin Films in Digital Light Processing (DLP) for Biobased Composites

ACS Applied Polymer Materials
Peer ...
Kontturi Eero, Baniasadi Hossein, Mousapour Mehrdad, Salmi Mika, Abidnejad Roozbeh, Babaeipour Sahar, Arumughan Vishnu, Fathi Ziba, Smal Ira   +8 more
openaire   +2 more sources

Performance measurements for indoor photovoltaic devices: Classification of a novel light source

APL Energy
There is an increasing interest in using indoor photovoltaic (IPV) devices to power Internet of Things applications, low power communications, and indoor environmental sensing.
D. E. Parsons, G. Koutsourakis, J. C. Blakesley   +2 more
doaj   +1 more source

Evaluation of the fused deposition modeling and the digital light processing techniques in terms of dimensional accuracy of printing dental models used for the fabrication of clear aligners

Clinical and Experimental Dental Research, 2021
Objective The objective of this study was to assess the accuracy of physical reproductions of plaster orthodontic study casts fabricated by two different rapid prototyping techniques: Fused Deposition Modeling (FDM) and Digital Light Processing (DLP ...
Samer T. Jaber, Mohammad Y. Hajeer, Tarek Z. Khattab, Luai Mahaini   +3 more
doaj   +1 more source

Advances in materials and technologies for digital light processing 3D printing

Nano Convergence
Digital light processing (DLP) is a projection-based vat photopolymerization 3D printing technique that attracts increasing attention due to its high resolution and accuracy.
Jisoo Nam, Miso Kim
doaj   +1 more source

Formulation-driven additive manufacturing of 3YSZ advanced ceramics via digital light processing

Open Ceramics
Zirconia is a key advanced ceramic due to its high mechanical strength, thermal stability, and biocompatibility. However, vat photopolymerisation-based additive manufacturing of zirconia presents challenges requiring advanced formulations and processing.
Athanasios Goulas, Basar Ozkan, Sina Saremi-Yarahmadi, Bala Vaidhyanathan   +3 more
doaj   +1 more source

Digital light processing (DLP) 3D-printing technology and photoreactive polymers in fabrication of modified-release tablets

European Journal of Pharmaceutical Sciences, 2019
In this study, we assessed the feasibility of using digital light processing (DLP) 3D printers (3DP) in fabrication of solid oral dosage forms. The DLP technology uses a digital micromirror device (DMD) that reflects and focuses ultraviolet (UV) light on the surfaces of photoreactive materials that polymerize in a layer-by-layer fashion.
Hossam Kadry, Soham Wadnap, Changxue Xu, Fakhrul Ahsan   +3 more
openaire   +2 more sources