Results 131 to 140 of about 36,960,886 (296)

The Effect of a Digital Manufacturing Technique, Preparation Taper, and Finish Line Design on the Marginal Fit of Temporary Molar Crowns: An In-Vitro Study. [PDF]

Biomedicines, 2023
Mugri MH, Dewan H, Sayed ME, Shaabi FI, Hakami HI, Jokhadar HF, Alqahtani NM, Alshahrani AA, Alabdullah AS, Alshehri AH, Wadei MHDA, Arif FY, Adawi EH, Al-Makramani BMA, Chohan H.   +14 more
europepmc   +1 more source

Integration of OpenCV‐Based Microscopic Adhesive Volume Measurement Into a Pyiron Workflow for Automated Data Analysis

Advanced Engineering Materials, EarlyView.
Residual adhesive after electrode loading in adhesive‐assisted resistance spot welding is quantified through a traceable experimental‐to‐digital workflow. Chromatic confocal topography provides calibrated surface‐height data, while OpenCV detects the electrode imprint and integrates adhesive height into comparable volume metrics.
Sung‐Min Wi, Jiangdong Zhao
wiley   +1 more source

Blockchain-Based Decentralized Digital Manufacturing and Supply for COVID-19 Medical Devices and Supplies. [PDF]

IEEE Access, 2021
Alkhader W, Salah K, Sleptchenko A, Jayaraman R, Yaqoob I, Omar M.   +5 more
europepmc   +1 more source

Superlubricity and Corrosion Inhibition Properties of Solvate Ionic Liquids in Hybrid Carbon Fiber Reinforced Plastic–Steel Interfaces

Advanced Engineering Materials, EarlyView.
Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees, Timothy Harte, Bhagya Dharmasiri, Y. Athulya Wickramasingha, David J. Hayne, Daniel J. Eyckens, Luke C. Henderson   +6 more
wiley   +1 more source

Jeffrey Manufacturing Company Factory Interior

, 1954
This photograph is an interior view of the Jeffrey Manufacturing Company factory in Columbus, Ohio, 1954.
The Jeffrey Manufacturing Company (Photographer)
core  

Model‐Guided Design of Paper Membrane Architectures for Controlled Flow and Enhanced Diagnostic Sensitivity

Advanced Engineering Materials, EarlyView.
Geometrical modifications on nitrocellulose membranes can result in observable differences in signal intensity relative to a reference membrane (top and bottom left). Using two reference experiments, we have developed a theoretical model that can reproduce the experimentally observed flow changes and provide information on membrane parameters, e.g ...
Maria Dimaki, Lea Holritz, Winnie E. Svendsen   +2 more
wiley   +1 more source

Jeffrey Manufacturing Company Aerial Views

, 1905
Three aerial views illustrate the growth of the Jeffrey Manufacturing Company plant in Columbus, Ohio ...
The Jeffrey Manufacturing Company (Photographer)
core  

Investigating the Effect of Inclination Angle and the Influence of Scan Parameters on the Appearance and Thermal and Mechanical Properties of Filigree Tension Rods of LPBF‐Manufactured NiTi Shape‐Memory Alloys

Advanced Engineering Materials, EarlyView.
This article investigates the dependence of the properties on the manufacturing orientation in the form of the inclination angle to the build plate of LPBF‐fabricated NiTi rods with a diameter of 150–220 µm. Metallographic, chemical, thermal, and mechanical characterization show behavior under identical manufacturing conditions that ranges from ...
Sandra Herzig, Michael Werner, Christian Rotsch   +2 more
wiley   +1 more source

Architecture‐Driven Sensor Stability in Weft‐Knitted Engineering Textiles

Advanced Engineering Materials, EarlyView.
Textile‐integrated sensor architectures are systematically compared to evaluate their electromechanical behavior under combined mechanical and environmental loading. Pocket‐based integration exhibits stable and reproducible signals, whereas tunnel‐based routing shows higher sensitivity accompanied by increased variability.
Adnan Maroof Khan, Johannes Wendler, Dilbar Aibibu, Johannes Mersch, Michael Wöltje, Chokri Cherif   +5 more
wiley   +1 more source

Quantitative Evaluation of an Industrial Robot Tool Trajectory Deviation Using a High-Speed Camera

Machines
One of the primary applications of industrial robots is in various manufacturing processes, such as milling, grinding, and additive manufacturing. To achieve the desired precision in tool trajectory performance when machining specific parts, it is ...
Mantas Makulavičius, Sigitas Petkevičius, Vytautas Bučinskas, Andrius Dzedzickis   +3 more
doaj   +1 more source