Results 131 to 140 of about 1,525,412 (268)

Effect of prior cold work on the mechanical properties of weldments [PDF]

, 2010
Heat exchanger units used in steam raising power plant are often manufactured using many metres of austenitic stainless steel tubes that have been plastically formed (bent and swaged) and welded into complex shapes. The amount of plastic deformation (pre-
Acar, Murat, Bouchard, Peter, Fitzpatrick, M. E., Gungor, Salih   +3 more
core  

Development and Preliminary In Vivo Study of 3D‐Printed Bioactive Glass Scaffolds with Trabecular Architecture

Advanced Engineering Materials, EarlyView.
This study reports the fabrication of trabecular bioactive glass scaffolds (composition “1d”: 46.1SiO2‐28.7CaO‐8.8MgO‐6.2P2O5‐5.7CaF2‐4.5Na2O wt%) through vat photopolymerization and the relevant results from mechanical testing and in vivo implantation procedures in rabbit femora, showing great promise for bone tissue engineering applications.
Dilshat Tulyaganov, Roberta Gabrieli, Avzal Akbarov, Nigora Nigmatova, Bekhzod Khabilov, Alessandro Schiavi, Martin Schwentenwein, Enrica Verné, Francesco Baino   +8 more
wiley   +1 more source

Measurement of local creep properties in stainless steel welds [PDF]

, 2012
A high temperature measurement system for creep deformation based on the digital image correlation (DIC) technique is described. The new system is applied to study the behaviour of a multi-pass welded joint in a high temperature tensile test and a load ...
Bouchard, J., Gungor, S., Sakanashi, Y.
core  

Adaptable Tile‐Based Pneumatic Origami through Structurally Coupled Localized Actuation

Advanced Engineering Materials, EarlyView.
This article presents tile‐based pneumatic origami structures with rigid tiles and flexible fabric creases, achieving adaptable properties including morphing shape, selective multistability, and tunable stiffness. Independently pressurized folding bladders at each crease enable structurally coupled localized actuation of origami structures.
Tiantian Li, Jonathan Luntz, Diann Brei
wiley   +1 more source

Input-output characterization of an ultrasonic testing system by digital signal analysis [PDF]

The input/output characteristics of an ultrasonic testing system used for stress wave factor measurements were studied. The fundamentals of digital signal processing are summarized.
Karaguelle, H., Lee, S. S., Williams, J., Jr.   +2 more
core   +1 more source

An Inkjet‐Printed Platinum‐Based Temperature Sensing Element on Polyimide Substrates

Advanced Engineering Materials, EarlyView.
An inkjet‐printed, meander‐structured, nanoparticle platinum‐based resistive temperature sensors on polyimide substrates are demonstrated as proof‐of‐concept. Optimized sintering at 250°C enables stable conductive structures. The Pt100‐ and Pt1000‐type sensors exhibit linear resistance–temperature characteristics with stable TCR in the 20°C–80°C range,
Shawon Alam, Thomas Kister, Alexander Scholz, Sophie Sauva, Makara Lay, Tobias Kraus, Jasmin Aghassi‐Hagmann   +6 more
wiley   +1 more source

Hybrid Auxetic Architectures: Integrating Curvature‐Driven Design for Enhanced Mechanical Tunability and Structural Performance

Advanced Engineering Materials, EarlyView.
Curvature‐tuned auxetic lattices are designed, fabricated, and mechanically characterized to reveal how geometric curvature governs stretchability, stress redistribution, and Poisson's ratio evolution. Photoelastic experiments visualize stress pathways, while hyperelastic simulations quantify deformation mechanics.
Shuvodeep De, Giovanni Meli, Meysam Khaleghian, Anahita Emami   +3 more
wiley   +1 more source

Discrimination of growth and water stress in wheat by various vegetation indices through a clear a turbid atmosphere [PDF]

Reflectance data were obtained over a drought-stressed and a well-watered wheat plot with a hand-held radiometer having bands similar to the MSS bands of the LANDSAT satellites.
Jackson, R. D., Pinter, P. J., Slater, P. M.   +2 more
core   +1 more source

Multimodal Mechanical Testing of Additively Manufactured Ti6Al4V Lattice Structures: Compression, Bending, and Fatigue

Advanced Engineering Materials, EarlyView.
In this experimental study, the mechanical properties of additively manufactured Ti‐6Al‐4V lattice structures of different geometries are characterized using compression, four point bending and fatigue testing. While TPMS designs show superior fatigue resistance, SplitP and Honeycomb lattice structures combine high stiffness and strength. The resulting
Klaus Burkart, Jonas Schmidt, Anastasiya Toenjes, Johanna Eisenträger   +3 more
wiley   +1 more source

Algorithmic Fairness and Digital Financial Stress: Evidence from AI-Driven E-Commerce Platforms in OECD Economies

Journal of Theoretical and Applied Electronic Commerce Research
This study examines the role of algorithmic fairness in alleviating digital financial stress among consumers across OECD countries, utilizing panel data spanning from 2010 to 2023.
Zhuoqi Teng, Han Xia, Yugang He
doaj   +1 more source