Results 21 to 30 of about 5,867 (211)
Batteries, 2018 Because of an increasing interest in NaSICON materials as electrolyte materials in all-solid state sodium batteries, their thermal expansion was investigated in this study.
Sahir Naqash +3 more
doaj +1 more source
Effect of Processing Route on the Microstructure and Mechanical Properties of Hot Work Tool Steel [PDF]
Materials Research, 2017 Powder metallurgy is a growing sector in industrial production, as it offers outstanding energy, cost and material savings in comparison with established processing routes such as casting.
Robert Besler +4 more
doaj +1 more source
Temperature-dependent thermal expansivities of silicate melts: The system anorthite-diopside [PDF]
, 1992 The temperature-dependent thermal expansivities of melts along the join anorthite-diopside have been determined on glassy and liquid samples using a combination of calorimetry, dilatometry, and Pt double bob Archimedean densitometry.
Knoche, Ruth +2 more
core +1 more source
Archives of Metallurgy and Materials, 2015 Recent achievements in the development of low-frequency high-resolution mechanical spectroscopy (HRMS) are briefly reported. It is demonstrated that extremely low values of the loss angle, ϕ, (tanϕb = 1×10−5) can be measured as a function of frequency ...
Magalas L.B.
doaj +1 more source
Dilatometry of ball milled nickel nano powder during non-isothermal sintering [PDF]
Science of Sintering, 2007 This work attempts to evaluate the sintering mechanisms of ball milled nanocrystalline nickel during nonisothermal heating. Samples showed a sintered density of 91.2% (theoretical) and grain growth up to 414 nm at 1273K.
Panigrahi B.B., Das K., Godkhindi M.M.
doaj +1 more source
Reheating of zinc-titanate sintered specimens [PDF]
Science of Sintering, 2015 The scope of this work was observing dimensional and heat transfer changes in ZnTiO3 samples during heating in nitrogen and air atmosphere. Interactions of bulk specimens with gaseous surrounding induce microstructure changes during heating ...
Labus N. +5 more
doaj +1 more source
The Influence of Silica Sand Granulometry and Sorting Level on Thermal Expansion [PDF]
Archives of Foundry Engineering, 2023 The quality of the castings depends, among other influences, on the quality of the moulding mixture used. The silica sands used are characterized by high thermal expansion compared to other sands. The tendency to dilatation of the moulding mixture can be
M. Bašistová, P. Lichý
doaj +1 more source
Unit cell dilation technique for analyzing dilatometry data [PDF]
, 2017 Dilatometry is the most accurate and common method for measuring the kinetics of phase transformations in solid specimens. Despite the development of a more accurate technique, an inferior method, i.e., the lever rule, is widely used in the scientific ...
Khodaie, N., Ivey, D.G., Henein, H.
core +1 more source
Characterisation of Mn0.63Zn0.37Fe2O4 powders after intensive milling and subsequent thermal treatment [PDF]
Science of Sintering, 2017 Commercial Mn-Zn powder (Mn0.63Zn0.37Fe2O4, 93 wt. % and Fe2O3 7 wt. %) was milled 0.5, 1, 2 and 4 hours in a planetary ball mill. The goal was to observe intensive milling influences on oxidation and reduction processes that will happen during ...
Labus Nebojša +7 more
doaj +1 more source
On the sensitivity of dimensional stability of high density polyethylene on heating rate
eXPRESS Polymer Letters, 2007 Although high density polyethylene (HDPE) is one of the most widely used industrial polymers, its application compared to its potential has been limited because of its low dimensional stability particularly at high temperature.
doaj +1 more source